Results 1 to 32 of 32
-
31-03-2008, 09:44 PM #1
hello problem with panasonik inverter
blinking the Timer light end no start.
-
31-03-2008, 10:14 PM #2
Re: hello problem with panasonik inverter
Could you give us some more details on the unit.
Model/Serial would be helpfull, also is it hard wired (controller on wall) or is it on a remote control.
If its hard wired, if you can give a fault code off the controller, i can give you the fault.
Sounds like its a problem with the set up of the timer.
Sorry, i cant be any more help than that at the moment
Regards
FatboyLast edited by Latte; 31-03-2008 at 10:15 PM. Reason: Essex Boy Spelling
-
31-03-2008, 10:36 PM #3
- Join Date
- Sep 2007
- Location
- Split Croatia
- Age
- 57
- Posts
- 6,151
- Blog Entries
- 6
- Rep Power
- 36
Re: hello problem with panasonik inverter
Hi Marko, welcome to RE forum!
Some help with language.
Ako imaš problema s jezikom pri opisu problema napiši na Hrvatskom ili Srpskom ili ako ti je to problem, napiši na Makedonskom, možda uspijem razumjeti problem i prenjeti drugim članovima na Engleskom.
Pozdrav, i preporučam da se predstaviš sa par rečenica na New to RE sekciji.
http://www.refrigeration-engineer.co...splay.php?f=72Last edited by nike123; 31-03-2008 at 10:38 PM.
-
03-04-2008, 09:20 PM #4
Re: hello problem with panasonik inverter
unite :CS-E12BKP
ako znate pomozi te mi
molim vas
-
03-04-2008, 10:22 PM #5
- Join Date
- Sep 2007
- Location
- Split Croatia
- Age
- 57
- Posts
- 6,151
- Blog Entries
- 6
- Rep Power
- 36
Re: hello problem with panasonik inverter
Koji je broj treptaja Timer lampe.
Obično, kad je greška te lampe trepnu određeni broj puta pa onda nastane pauza. Koji je tvoj slućaj?
Translation.
Marko: Unit is Panasanic CS-E12BKP.
IF you know codes, help me please!
Me: What is number of blinks.
Usually, when we have error there is certain number of blinks connected with that error. What is your case?
-
04-04-2008, 12:24 AM #6
Re: hello problem with panasonik inverter
Nike don't know if you need to translate the following guide.
-
04-04-2008, 03:24 AM #7
Re: hello problem with panasonik inverter
Yeah, as above.
A blinking light just indicates an error. To find the fault, hold down the check button for 5 sec on the remote controller until a 'H' code appears on the remote controller display.
Then use the time up and down buttons on the remote to scroll through the fault codes. When you get to the code that applies, the indoor unit will beep 4-5 times. That's the fault code.
attached is the fault codes for this modelLast edited by paul_h; 04-04-2008 at 03:38 AM. Reason: attachment
-
04-04-2008, 07:52 AM #8
- Join Date
- Sep 2007
- Location
- Split Croatia
- Age
- 57
- Posts
- 6,151
- Blog Entries
- 6
- Rep Power
- 36
Re: hello problem with panasonik inverter
Marko ovo je opis. Kad nađeš grešku, ako trebaš prevod i pomoć postaj koji je kod u tvom slućaju.
Pozdrav, NikeDijagnostika greški
Kod greške koristi se samo na Inverter Sistemima. I Single i Super multi Inverter sistemi koriste jednake kodove greške kao niže.
Kodovi vanjske jedinice koriste se SAMO kod Super Inverter multi sistema, model 23 i 27, a ne koriste se kod mono invertera.
Kada se dogodi greška Tajmer lampa počinje bljeskati i uređaj stane s radom.
Isključivanje napajanja će resetirati jedinicu ali neće izbrisati kod greške.
Uređaj pamti do tri koda greške.
Pronalaženje koda greške.
Osigurajte da je uređaj uključen i usmjerte daljinski upravljač prema njemu tako da može primiti signal.
Za single sisteme (CSE i CSXE) pritisnuti CHECK dugme više od 5 sekunda.
Za multi sisteme (CSME) pritisnuti Timer Setting strelicu prema gore više od pet sekunda.
H11 će se pojaviti na zaslonu daljinskog upravljača - to kazuje da je aktivan mod testiranja.
Koristite Timer Setting strelice prema gore i dolje za pomicanje između kodova greške sve dok se ne čuju četri bipa - to pokazuje kod greške.
Kodovi greške se čiste iz memorije namještanjem rada na Test Colling i kratkog spajanja RESET terminala u pretincu za bateriju daljinskog upravljača.
-
04-04-2008, 10:53 PM #9
Re: hello problem with panasonik inverter
hvala puno NIKE 123 .
nisam jos pokusao ali uradicu to i javicu se opet.
jos jednom HVALA pomoci.Last edited by marko.manev; 05-04-2008 at 09:58 AM.
-
05-04-2008, 10:02 AM #10
Re: hello problem with panasonik inverter
na displeju se javilo kod H11
Ali neznam kako da je pustim u mod Test Cool da bi izbrisao greske jer ovaj kod pokazuje da nije dobar kontakt izmegu oba jedinica.Pronasao sam gde je prekid ali samo ne mogu izbrisati gresku jos uvek treperi Timer.
Ako mozes objasni mi kako je postupak.
Unapred hvala.
-
05-04-2008, 10:21 AM #11
- Join Date
- Sep 2007
- Location
- Split Croatia
- Age
- 57
- Posts
- 6,151
- Blog Entries
- 6
- Rep Power
- 36
-
05-04-2008, 08:13 PM #12
Re: hello problem with panasonik inverter
Izvini druze neznam dali sam ja glup ali na ovaj Dalinski upravljac nemam dugme (test cool)i zato neznam gde uopste da ga trazim .
Ako hoces i slikacu dalinski upravljac i poslacuti da vidis dali je moguce da se nesto uradi .
Samo mi daj tvoj e-mail i odma ti ga saljem.
Dali je to dugme na dalinskom ili na samoj klimi?
Stvarno sam u zabludi.
-
05-04-2008, 09:22 PM #13
- Join Date
- Sep 2007
- Location
- Split Croatia
- Age
- 57
- Posts
- 6,151
- Blog Entries
- 6
- Rep Power
- 36
Re: hello problem with panasonik inverter
Jesi li je isključio skroz na osiguraču?
Imaš li Auto switch na klimi i Reset na daljinskom?
Ako imaš, stisni Auto switch i drži pritisnutim dok ne čuješ beep a onda na daljinskome stisni Reset.
Mail imaš u mojoj V-card. http://www.refrigeration-engineer.co...=vcard&u=13885Last edited by nike123; 05-04-2008 at 09:30 PM.
-
05-04-2008, 10:52 PM #14
Re: hello problem with panasonik inverter
Hvala ti puno na pomoci .Neznam kako da ti se oduzim.Sutra cu probati da resim problem,Hvala ti jos jednom.Ako mozes dodji tu i vodim te u KAFANU.
-
05-04-2008, 10:54 PM #15
- Join Date
- Sep 2007
- Location
- Split Croatia
- Age
- 57
- Posts
- 6,151
- Blog Entries
- 6
- Rep Power
- 36
Re: hello problem with panasonik inverter
Last edited by nike123; 05-04-2008 at 11:00 PM.
-
05-04-2008, 10:55 PM #16
Re: hello problem with panasonik inverter
Ma nema problema za drustvo sa puko.
-
05-04-2008, 10:59 PM #17
Re: hello problem with panasonik inverter
Imas li SKYPE ,ako imas mozemo se dopisavati i mnogo brze.Salem ti kako da me trazis :Makedonija,(meto.manev)
-
05-04-2008, 11:01 PM #18
Re: hello problem with panasonik inverter
Evo ti i moj Deleted
Last edited by chillin out; 06-04-2008 at 11:33 AM. Reason: Please do not post e-mails.
-
05-04-2008, 11:20 PM #19
- Join Date
- Sep 2007
- Location
- Split Croatia
- Age
- 57
- Posts
- 6,151
- Blog Entries
- 6
- Rep Power
- 36
-
06-04-2008, 03:41 AM #20
Re: hello problem with panasonik inverter
How does he know he's corrected the problem. I mean if you turn the power off to the units for 2min, then fault doesn't clear, it's because he hasn't corrected the problem, no because he can't reset the units.
See if 20-30 volts is between neutral and signal wires, if there is, it means outdoor unit PCB is good.
I don't know how to test the indoor unit PCB, but if the unit is still giving h11 fault, and outdoor unit good (20-30volts), then indoor unit PCB faulty.
-
06-04-2008, 10:44 AM #21
- Join Date
- Sep 2007
- Location
- Split Croatia
- Age
- 57
- Posts
- 6,151
- Blog Entries
- 6
- Rep Power
- 36
Re: hello problem with panasonik inverter
He followed instruction about acquiring and reseting codes I translated from general instructions for alarm codes posted by Electrocoolman. There is reset procedure described different then in your attachment. Then I instructed him that reset unit as described in your attachment. He will try today.
Last edited by nike123; 06-04-2008 at 10:47 AM.
-
06-04-2008, 11:01 AM #22
Re: hello problem with panasonik inverter
It's impossible to make anything foolproof because fools are so ingenious...
Don't ever underestimate the power of stupid people when they are in large groups.
Please, don't teach me how to be stupid....
No job is as important as to jeopardize the safety of you or those that you work with.
-
06-04-2008, 06:25 PM #23
Re: hello problem with panasonik inverter
Epa ovako drustvo probao sam kako ste vi rekli ali mislim da nisam resio problem.Resetirao sam memoriju.Ali nakon novog uklucivanja u rezim rada ona se opet vrati i pokazuje opet onaj isti H11(problem).i neznam sta vise da radim ,ja mislim da ima neki problem oko kompresoru zato sto do nadvoresnoj jedinici dolazi napon 220V,a on ipak ne startuje .
Ako znate nesto molim vas recite slobodno.
-
06-04-2008, 07:01 PM #24
- Join Date
- Sep 2007
- Location
- Split Croatia
- Age
- 57
- Posts
- 6,151
- Blog Entries
- 6
- Rep Power
- 36
Re: hello problem with panasonik inverter
-
06-04-2008, 07:38 PM #25
Re: hello problem with panasonik inverter
Jeste isao sam kako sta si rekao.Na displeju dalinskog se pojavio kod H11 i kada sam isao gore i dole na streicama tajmera kada opet dodje na H11 ona bipni cetri puta.A kada sam probao resetirati je, zadrzim je na auto start sve dok ne napravi bip,a onda ona sama startuje u auto mod,i nakon toga stisnem i reset ali nikakav zvuk se ne cuje i ona zaustane i nastavi treperiti timer .
-
06-04-2008, 07:49 PM #26
- Join Date
- Sep 2007
- Location
- Split Croatia
- Age
- 57
- Posts
- 6,151
- Blog Entries
- 6
- Rep Power
- 36
Re: hello problem with panasonik inverter
Onda greška nije otklonjena. Provjeri osigurače u vanjskoj jedinici.
Napon na vanjskoj jedinici između nule i signalnog voda treba biti 20-30V. Ako ga ima, onda bi trebala biti greška na elektronici u unutarnjoj jedinici a ako nema onda je greška na elektronici u vanjskoj jedinici.
As Paul said he did not corrected the problem and I instructed him as Paul suggested. Does anyone have service manual for this unit?
-
06-04-2008, 08:06 PM #27
-
06-04-2008, 08:40 PM #28
- Join Date
- Sep 2007
- Location
- Split Croatia
- Age
- 57
- Posts
- 6,151
- Blog Entries
- 6
- Rep Power
- 36
-
06-04-2008, 09:04 PM #29
Re: hello problem with panasonik inverter
Ako hoces prati i meni.
Merio sam napon i megu nulu i desni Signalni kontakt i tu ima neki mali napon ali nema sto kazes 20 -30 volta,merio sam i osiguraci u vanskoj jedinici ,oni su ispravni.moj e-mail je (m.marko@freemail.com.mk)
-
06-04-2008, 09:12 PM #30
- Join Date
- Sep 2007
- Location
- Split Croatia
- Age
- 57
- Posts
- 6,151
- Blog Entries
- 6
- Rep Power
- 36
-
06-04-2008, 11:21 PM #31
-
07-04-2008, 12:10 AM #32
- Join Date
- Sep 2007
- Location
- Split Croatia
- Age
- 57
- Posts
- 6,151
- Blog Entries
- 6
- Rep Power
- 36
Similar Threads
-
Testing Inverters
By fridge doctor in forum Air ConditioningReplies: 38Last Post: 15-06-2011, 06:52 AM -
A strange problem
By MuhengineeR in forum Air ConditioningReplies: 14Last Post: 27-10-2010, 05:21 PM -
daikin L0 inverter problem
By robin r33 gtr in forum Air ConditioningReplies: 17Last Post: 11-03-2010, 11:25 PM -
Problem with an inverter compressor in V.R.V system DAIKIN R 407
By Harris Greece in forum Air ConditioningReplies: 10Last Post: 24-11-2007, 12:53 AM -
strange inverter problem
By rbartlett in forum Air ConditioningReplies: 11Last Post: 19-05-2006, 08:31 PM