INVESYS ECH 210B PASS help

[dfranc]

Please repairmen, if they have a password to enter the parameters of the purchased second-hand Invensys ECH 210B controller?

This would replace my defective pictured below. Thanks in advance. Cheers







Cela remplacerait mon défectueux dans l'image ci-dessous. Merci d'avance. Salutations









upload pics in a link




This would replace my faulty one in the image below. Thanks in advance. Cheers


Please if you have a technical manual for this heat pump.

[dfranc]

Sorry for my bad English, if you can help me I will be very grateful. Greetings

[al]

Try 22 or 12, it looks a bit like an elliwell.

[dfranc]

Thank you, but unfortunately it is not, it is an Invensys ECH210B controller.Thanks, but unfortunately it's not, it's an Invensys ECH210B regulator. Do you maybe know where to get it,"ModbusRequestPro" Regards Greetings

[redroge]

It could be 177

[Peter_1]

Or 135 for all Eliwell

[dfranc]

Thank you, but unfortunately it is not.This is the answer from the Elliwell help desk!Regards Greetings



Dear sir,

I am sorry but we do not know the password.

Passcode has been set by the appliance manufacturer and there is not way to bypass it

Thanks

[dfranc]

Please if you have a technical manual for this heat pump.

[frank]

There is a contact link on their web page for this model

https://brightcac.diytrade.com/sdp/4..._recovery.html

Or you could just replace the controller with a new Eliwell or similar

[dfranc]

there is a contact link on their web page for this model

https://brightcac.diytrade.com/sdp/4..._recovery.html

or you could just replace the controller with a new eliwell or similar

mozilla_pkix_error_required_tls_feature_missing

[jero]

Did you try pass 77?

[frank]

mozilla_pkix_error_required_tls_feature_missing

Link Working fine this end

[dfranc]

Link Working fine this end

https://brightcac.diytrade.com/sdp/435477/4/home/0.html

I managed to open this, but my pump is missing?

[frank]

But the contact link is there, so you could email them for help

[Peter_1]

Thank you, but unfortunately it is not, it is an Invensys ECH210B controller.Thanks, but unfortunately it's not, it's an Invensys ECH210B regulator. Do you maybe know where to get it,"ModbusRequestPro" Regards Greetings

Invensys = ELIWELL

[frank]

Invensys is now Schneider Electric
https://www.se.com/ww/en/brands/invensys/invensys.jsp

[dfranc]

Invensys = ELIWELL

It's better to keep your mouth shut and give the impression that you're stupid than to open it and remove all doubt.



I didn't understand this.

[dfranc]

HI
another Modbus Request Software : Modscan32 or 64
available here in demo mode (or with license):https://www.win-tech.com/
a quick demo :https://www.youtube.com/watch?v=STBX1Nc2I0s

[dfranc]

Could you access the ECH 210B parameters with this keyboard?

[jero]

Yes,but you still need password

[dfranc]

I tried from 0-255, and it won't open the parameters, there isn't even a -set- mark, and on the old one, when I press both buttons, it first shows -set-, and then it goes on to PAR-CONF, H1, etc.

[jero]

what problem do you have? why do you need to enter to the parameter? change what?

[dfranc]

This is the second controller, which needs to replace my old one, but it was on another pump, so the parameters need to be changed, which is an impossible mission. It seems that the factory or the former owner turned off the pass and code to enter the config mode. Now I can't learn even with modscan, not even with Dial_ECH2XX_ModBus_1.1.3, and modbusreqestpro, I can't find it. Regards

[dfranc]

I got Ellivel ECH 210bdt, and with the password 199 I enter the config settings, but I can't learn everything. I should probably use another service password? I don't have access to H5, 6, 7, 8 and many other parameters?

[dfranc]

I got the instructions here, but I haven't tried it yet. Greetings

https://chaleurterre.com/forum/viewt...162271#p162271



private image upload

[dfranc]

A password will be requested to perform this operation
On the display, it is shown - - -• Type the password value corresponding to the parameter value Pa H47 ,,,,neeting - - -• Il n'y a pas de possibilité d'entrer un mot de passe,,,,,










Nothing! There is no possibility to enter a password

Either the copy card is faulty or it needs to be formatted, but how?

[dfranc]

Good morning! A new used 9Kw heat pump has arrived, Slovenian version from Technibel.