all reefer container problems/daikin/carrier/thermoking/mitsubishi

[absolute-zero]

hey M L CA ... sounds like you need to wire your condenser fan to run all the time. that should be fine with R404a as you needed the cycling action with R134a to keep the head pressure up in cold ambients.

the reason its tripping is cause it wants to pump down on defrost but because the fan is off it builds head and trips fast even before it can shut off. you may have a problem with the cycle switch as it should cut in on a rise in pressure. i have seen before that the compressor contactors stick and work erratically at best. we always lube those contactors.

Or it may possibly be overcharged with refrigerant.

[bruisermac]

yes it could...it is hard to help a guy over the internet isnt it...the best is when they say its messed up but the pressures are "good" that is funny sh@t!!!

[absolute-zero]

yes it could...it is hard to help a guy over the internet isnt it...the best is when they say its messed up but the pressures are "good" that is funny sh@t!!!

Yeah sometimes its a challenge. My favorite one is "I think the pressures are okay, I will hook up gauges and check". I posted a what is normal pressure work sheet some where on this forum maybe a year and half ago.

R-T

[saleemsalem]

Hi saleemsalem

did you check TR(transformer)? You try replace the transformer with new one. Good luck.

reefer mechanic.

Actually I did not replaced the Transfotmer, because its output Voltages were Normal 18volts and 22volts AC.

[absolute-zero]

Actually I did not replaced the Transfotmer, because its output Voltages were Normal 18volts and 22volts AC.

I think Reefermech was thinking that if the voltage leaving the transformer was higher that this could cause higher current draws for the controllers devices. This does make logical sense, but since you have proper voltage on the secondary, then transformer is not the issue.

You have changed the controller twice and still pops the fuses, do you know exactly when the fuses pop? Do they pop right away or does the unit continue through its start up sequence and then pop. If so in which part of the sequence does the fuse blow? During Evap fan start up, during condensor fan start up, during compressor start up? Typically this will give you clues as to what device that the controller is blowing the fuse on.

If it is popping right away then you will probally have to get out your DMM and perform a resistance check on all inputs and outputs for a path to ground or internal low resistance due to a faulty shorted electrical device.

Let us know what you find

A-Z

[teguh]

Hi William,
As I know, just go to misc. function menu to reset time and date. No need password.

[starezone]

Good day.
i'm a biginner technician in reefer side.i want to bay some data retreive connector .but i have problem to found them ...
can some body assist.
badilou.nabil@hotmail.com

[teguh]

everybody,
sorry, wrong post yesterday

[khoadg]

Hi Opieman.

İ think i found service manual of your machine.You need which one??

RD-II and RD-II MAX (TK40181-1-MM).pdf

RD-II Max (TK41023-1-MM Rev 1 10-27-03).pdf

RD-II SR (TK41131-1-MM Rev 04-03).pdf

RD-II TCI & RD-TLE (TK50394-1-MM Rev. 2-99).PDF



Also you give to me your mail adress.İ will send to you)))

See you,

Reefermechanic

Hi!
Please help to send these manuals to my email: khoadg@yahoo.com
Thank a million!

[Will]

Whats ya doing teguh ? lol

[deliazmi]

Does anybody have documents about general principles of reefer's control system and how it designed? Information about connection of sensors,cable diagrams and repair manuels would hellp me too, Thank you..

[ci_1612]

I have a carrier 511-362 thats going off on Alarm 15 but that alarm does not appear on the list of alarm codes on the reefer or in the manual that I can locate...if you know what this means let me know. I'm a newbie and working by myself and don't really want to call someone else in if its just something stupid.

[Will]

carrier 511-362 thats going off on Alarm 15 but that alarm does not appear on the list of alarm codes on the reefer or in the manual

Later models show that alarm as "loss of cool". I'm guessing yours has gone through some software upgrades and thus won't show newer alarm # on the door.
Go to Carriers website and check out the later model PDFs.

[teguh]

The latest SW ver. is 5146.

[rig19elect]

Hi guys,
I am new to this site. I have 2 faults codes on sr-2 alarm window: 4 and 204. I found a plastic back stuck in evaporator so it was preventing airflow. I fixed but need to reset these codes. Can anyone pls help.
Thanks

Jesmond
Rig19 Electrician

[reefermechanic]

........................

[toddymcbride]

hi, only new to this site and new to transport Refrig. I have just recently started work on a Truck with an RD11 50SR 380V
B/M No. 915527. on R404a ...
the in cabin computer is a Thermoking Thermoguard Base - 5D52175G01
S.P 45-1066
The problem that has been occuring is the unit runs until the temp decreases to about 2degrees C then unit cuts into defrost then cools again then defrosts etc etc..

The screen showed just before defrosting
Room 1.3oC
DIS -2.7oC
Coil -7.2oC

Set up for DF1 4 and DDR 45
The air pressure switch has been disconnect. I have checked the operating pressures 120kpa suction and 1650 kpa Head pressure. I hosed out condensor coil and check evap conditon No ice on coil..

What does

(("SELECTING CYCLE SENTRY OR
CONTINUOUS MODE"
1. Press the On Key to turn the unit on.
2. Press the Select key to display [CYCLS]
and [YES] or [nO].
3. Press the Up or Down Arrow key to
select the desired mode. [YES] = Cycle
Sentry, [nO] = Continuous.
4. Press the Enter key. The display will
briefly show [Lod], and then the new mode

will reappear.))

Is it possible to change how the unit activates defrost.? becuase the owner only uses the truck for about 4 hours a day can the defrost relay be removed ?? I would appreciated any help or ideas!!

[ppsmtu]

hi
good day
i want to know aboutthermo king reefer unit on message (quest not allowed by timer). can u explain me and how to clear this message ?
thanks you
pyae

[reefermechanic]

.............................................

[pacoperez60]

hello sr, I HAVE A PROBLEM WITH MY REFEER , HAS THIS MESSAGE. ENGINE STALLED. IDONT NOT WATH IS THAT CAN YOU HELP ME IM SORRY FOR MY BAD WRITER THANX SO MUCH

[pacoperez60]

I forgot my unit its a carrier ultima53 year 2000

[reefermechanic]

I forgot my unit its a carrier ultima53 year 2000

hi pacoperez,

first nice too meet you.I think your unit is truck or trail unit.I repairing reefer container units.I cant help you..Sorry...

see you

reefer mechanic..

[altics]

Hi Opieman.

İ think i found service manual of your machine.You need which one??

RD-II and RD-II MAX (TK40181-1-MM).pdf

RD-II Max (TK41023-1-MM Rev 1 10-27-03).pdf

RD-II SR (TK41131-1-MM Rev 04-03).pdf

RD-II TCI & RD-TLE (TK50394-1-MM Rev. 2-99).PDF



Also you give to me your mail adress.İ will send to you)))

See you,

Reefermechanic

hi...can you give me some link...heres my my email add.....agonish_04@yahoo.com

[triardi]

Dear Reefer Mechanic,

Would you like to sent me Service Manual / Operating Manual of Reefer Container "DAIKIN" LXE 10 D ?

My Email Address is tri_ardi@yahoo.com

Best Regards,
Triardi S.

[topbanana]

Dear bro...
When i was doing pti (thermoking unit,magnum), alarm 115 and 116 were come out.it does mean sensors faulty but when i check connection and ohm,showing that all in good condition (2000 ohm) please help me how should do?

[reefermechanic]

.....................

[terminal]

HAY ALL,
i am technician in the reefer , pls i have probleme with t.KING ( quest allowed) i want to clear it but i need help .

BESTB REGARD

[topbanana]

Sorry for late reply,mate ! I haven't try to change yet coz i haven't spare part yet but i'll be change return air sensor and reply you no sooner.
Thank you so much for your reply.

[topbanana]

Thanks a ton. It's really worked!
When i was changed return air sensor , the unit is ok and pti pass.....i am quite curious coz the measure the value of ohm is nothing different with the old and new one sensor..? ?

[teguh]

Hi, banana
Try icebath calibration

[reefer-tech]

hi
good day
i want to know aboutthermo king reefer unit on message (quest not allowed by timer). can u explain me and how to clear this message ?
thanks you
pyae

Hi, you shouldn't need to clear this. Quest is a power saving initiative. Starcool and ThermoKing also use it, Daikin call it DTMS2.
It is exactly as you state "a message". It is telling you that the power saving mode (Quest) is currently not active due to a controller initiated time delay.
As per Reefermechanic's menu picture, it is in the MISC sub menu Under STATUS.
Quest should be left to do what it is supposed to, and only turned off if you have a very good reason :-)

"QUEST power-saving mode is a software-based control option for Carrier Transicold refrigeration units that intelligently cycles refrigeration on and off based on temperature limits designed for specific perishables. It can cut energy requirements for refrigeration by up to 50% while also reducing power-related emissions."

[faiq sulafi]

pak teguh...
punya softwere untuk daikin, \tk, mitshubisi.
kalo ada boleh untuk di share ke saya
terima kasih

[zaher adidas]

Please i need manuel for trailer theroking

[zaher adidas]

Please i need manuel for trailer theroking ANYONE CAN HELP ME SEND IT TO ZAHERADIDAS@HOTMAIL.COM

[reefersup]

plz i have probleme with dakin for f 803 END F109; I WANT TO KNOW THE GOOD SOLUTION FOR THIS PROBLEME;THINKS MY TETCHER

hi the problem is ev .u must adjust ev or change it . tnks:reefer sup

[reefersup]

note that it's no alarm ,i thinc sae tect reefer play in cofiguration i check and i bac whit good ansower. tnks/reefer sup

[reefersup]

HAY ALL,
i am technician in the reefer , pls i have probleme with t.KING ( quest allowed) i want to clear it but i need help .

BESTB REGARD

note that it's no alarm ,i thinc sae tect reefer play in cofiguration i check and i bac whit good ansower. tnks/reefer sup

[nickzarin]

Hi reefermechanic ,can you advice me on truck unit - T/K Spectrum MT ?

[nickzarin]

PM me .tq.

[ci_1612]

I have an old carrier 511-331. Its not modulating at all and also seems to be turning on only when the return comes 1 degree over set point and will go down 4 or so degrees under setpoint. Now I havent spent much time on it but have tested power coming to the plug connected to the stepper motor..I have voltage coming through on all 4 lines.. Should only have power on A/B or C/D at one time as A/B open and C/D close it if my memory serves me correctly. So that tells me the stepper motor itself is not the issue, however does this mean somehow it is the microlink or could it be the power module or even something else? just trying to get another opinion as it is a leased box and I cant just start changing random parts. P.S I did check to see if quest software was on this box and it is not.

[morino_55]

dear all;
first happy now year;i have reefer daikin with AL :d301;but i dont new the solution,plz help me urgently

[bruisermac]

hey 1612

check for broken wires behind the compressor and suction valve. they rub on the back wall sometimes. also the drive module or if its an APL the emergency module fails. if it has an emergency module remove it and plug into the SMV directly

[starezone]

good day evey body .
i look for some advice from the refrigeration-engineer experiance.
me issus is i can found the stare cool reefer unit softwear to import the data logger from this unit..
please advice .
badilou.nabil@yahoo.com

[nunogato]

Hi

I need 2 manuals for these equipments:

ThermoKing MDII-MAX
Carrier Mistral 800

please send it to nunovgato at gmail.com

Thanks

[climo-tecnica]

alguien en español por favor nesesito datos diagramas de carrier intercambio informacion tengo todo de thermo king grasias ggeras@hotmail.com

[transcold]

Hi Climo-tecnica,
Could you speak in English?

[transcold]

Hi Ci 1612,
I think you should check CD18 CD20 and CD34 to verify the setting of configuration, software versions and Economy mode.

[transcold]

Hi Starezone,

Please receive email for software.

[Dante]

Hi, reefermechanic

Im Dante, can I charge a Carrier reefer with 404a its present refrigerant is 134a?....Pls. give me more info about this. Thanks

Dante

[transcold]

Hi Dante,

I think you can not charge it with R404a. Because the working pressure of R404A is too high to fit this pipe system. and the components, for example compressor, TXV, HPS.... are not suit R404A.

transcold.