all reefer container problems/daikin/carrier/thermoking/mitsubishi

[reefermechanic]

...................

reefer mechanic

[Will]

Welcome Reefermechanic.

What ?, no StarCool ?

[reefermechanic]

Hi Will,

Only, MAERSK using Starcool unit.Also i repaired a few unit but ı don't know everythings about starcool unit.What happen??You have problem starcool unit?Maybe i can help you)))

[zaher adidas]

Please i need manuel for trailer theroking

[akhtar nadeem]

hello pls tell me about starcool cantainer plant mostly coming problems thanks

[mgc-amc16]

Hapag Lloyd and Cma-cgm also

[why me?]

hello i was sent to an old carrier container wwhen i got there room temp plus 20 no ref running turn stat to minus 10 ref ran set stat to zero fridge ran to plus 10 then
stopped turned down to minus 10 ref
restarted can you help?

[reefermechanic]

hello i was sent to an old carrier container wwhen i got there room temp plus 20 no ref running turn stat to minus 10 ref ran set stat to zero fridge ran to plus 10 then
stopped turned down to minus 10 ref
restarted can you help?

Hi Why Me

can you say to me whats model your carrier unit??for example 69NT40 -489 etc....

Best regards.

Reefermechanic.

[Tifare Jone]

hi,Im new need to know how to daignose thermoking relay board>mp3000

[ramakrishna]

Dear Sir,

I have problem with my container refrigeration unit. It is carrier transicold unit model no.69NT40-511-11. When start the unit compressor is getting full frosting. Can you help me to solve this problem?
Thanks & Regards

Krish

Welcome Reefermechanic.

What ?, no StarCool ?

[kheilan]

Dear to all RE:

I need some advice because i will conduct a flashing. the unit is carrier although i have experience to do that but i want to have advice for some important to because the last compressor of that unit is broken so we buy a new compressor.

thank you and regards to all out there ^^

[reefermechanic]

Dear Sir,

I have problem with my container refrigeration unit. It is carrier transicold unit model no.69NT40-511-11. When start the unit compressor is getting full frosting. Can you help me to solve this problem?
Thanks & Regards

Krish

Hi Krish

Some times that s normal. But some times that s not normal. Yo have to check step by step below mationed;

* You have to do P-6 SMV test, pass or fail?
* You have to check refrigerant level in the system. Maybe refrigerant level is too much??
* You have to check TXV.


If all them ok below mationed no need repair to your unit...

Good luck.

see you

Reefer mechanic.

[ramakrishna]

my dear friend,

thank you very much for the suggession. container is in transit and will do the test once it reach.

Thanks & Regards

Krish

[johnson.lee.biu]

I have a problem with a Daikin Reefer reciprocating semi hermetic compressor that was pull out some time ago. The 9 terminals on the compressor have no leads and were not marked. I need to run this compressor but do not have the wiring diagram. The model no.2HC5BLB-L and was for a Daikin Reefer container manufactured in the 1970's. Could someone show me how to wire up this compressor that as I have mentioned has 9 terminals. I am completely lost.

[reefermechanic]

I have a problem with a Daikin Reefer reciprocating semi hermetic compressor that was pull out some time ago. The 9 terminals on the compressor have no leads and were not marked. I need to run this compressor but do not have the wiring diagram. The model no.2HC5BLB-L and was for a Daikin Reefer container manufactured in the 1970's. Could someone show me how to wire up this compressor that as I have mentioned has 9 terminals. I am completely lost.

Hi johnson.lee,

Is it 2HC58LD-R ? Pls check again its for correct model number. So pls check to the container unit model number.

see you

reefermechanic

[johnson.lee.biu]

Thanks for a response, the name plate does fade abit.
Anyway does 2HC58LD-R has 9 terminals? It looks like a dual voltage 200volts 3 phase and 440 volts 3 phase.
How do I know which terminals is for 440 volts and which terminals are for 200 volts. A wiring diagram would help a great deal. Hoping for your reply.
Johnson

[reefermechanic]

Thanks for a response, the name plate does fade abit.
Anyway does 2HC58LD-R has 9 terminals? It looks like a dual voltage 200volts 3 phase and 440 volts 3 phase.
How do I know which terminals is for 440 volts and which terminals are for 200 volts. A wiring diagram would help a great deal. Hoping for your reply.
Johnson

Hi Friend,

Pls check your email box

see you

reefermechanic

[opieman74]

Hi. Iam a commercial refrigeration tech and owner. I was just recently asked to repair and services a thermo king unit M/N RD II 30. I am looking for a services manual or where to get one. Could you tell what kind of problems to look forword to.

[reefermechanic]

Hi Opieman,

I didn't understand you.But you must tell me right model.Your machine marine or trailer units??Beacuse on the Thermoking container units signs CSR,CRR and Magnum etc.If you give to me more information i will help you..

Best Regards.

reefermechanic

[reefermechanic]

Hi Opieman.

İ think i found service manual of your machine.You need which one??

RD-II and RD-II MAX (TK40181-1-MM).pdf

RD-II Max (TK41023-1-MM Rev 1 10-27-03).pdf

RD-II SR (TK41131-1-MM Rev 04-03).pdf

RD-II TCI & RD-TLE (TK50394-1-MM Rev. 2-99).PDF



Also you give to me your mail adress.İ will send to you)))

See you,

Reefermechanic

[abbsnowman]

Hi reefermechanic and welcome.
I think your calling truck / trailer units container units. On this side of the pond, container reefers are "sea going" containers.
One last thing, you may get some flack for offering manuals here. If you decide to help someone this way, it's best to email them with the offer.
I apreciate your wanting to help but some others may not.
Cheers
Abbs

[Luisillo]

Hi reefermechanic and welcome.
I think your calling truck / trailer units container units. On this side of the pond, container reefers are "sea going" containers.
One last thing, you may get some flack for offering manuals here. If you decide to help someone this way, it's best to email them with the offer.
I apreciate your wanting to help but some others may not.
Cheers
Abbs

por favor me podrias mandar tambien los manuales, ya que soy nuevo en esto, te lo agradeceria.

[khoadg]

Hi Opieman.

İ think i found service manual of your machine.You need which one??

RD-II and RD-II MAX (TK40181-1-MM).pdf

RD-II Max (TK41023-1-MM Rev 1 10-27-03).pdf

RD-II SR (TK41131-1-MM Rev 04-03).pdf

RD-II TCI & RD-TLE (TK50394-1-MM Rev. 2-99).PDF



Also you give to me your mail adress.İ will send to you)))

See you,

Reefermechanic

Hi!
Please help to send these manuals to my email: khoadg@yahoo.com
Thank a million!

[Will]

Whats ya doing teguh ? lol

[altics]

Hi Opieman.

İ think i found service manual of your machine.You need which one??

RD-II and RD-II MAX (TK40181-1-MM).pdf

RD-II Max (TK41023-1-MM Rev 1 10-27-03).pdf

RD-II SR (TK41131-1-MM Rev 04-03).pdf

RD-II TCI & RD-TLE (TK50394-1-MM Rev. 2-99).PDF



Also you give to me your mail adress.İ will send to you)))

See you,

Reefermechanic

hi...can you give me some link...heres my my email add.....agonish_04@yahoo.com

[LTP-Jon]

Hi. I'm searching high and low for software to allow connection to the Mitsubishi MMCC3A unit on refrigerated containers. It's usually called "Mitsubishi Heavy Industries Data Logger System". Would anyone know where this is available to download? Thank yo very much.

[Will]

Hi Jon, welcome to RE.

Is this what your looking for ?

http://truck.mhi.co.jp/gen/acrmw/ser...orma/act5.html

[bruisermac]

call up StarCOOL and they will send you the manuals. They have them on the site but you have to register to get the access.

[alphalaval]

hi there, can i have some thermoking and xrios 500 service manual/ wiring dia gram.

khalidmz786@hotmail.com
thanks
khalid

[abet_meneses]

Reefer mechanic,

welcome to RE and nice to have a new member who are more than willing to help and share his knowledge.

regards,

[dglaab]

Hi guys:

I have 4 carrier elite and thinline shipping container units rnning a holding room here. I would really like to intergrate their electronics with my plant plc so I could do things like initiate defrosts from it, and monitor them. Does anyone have any access to or ideas on either electrical schematics or interface programs for this?

thanks

Dan

[esseuro]

Hi Dan,

If you just want the basics like manual defrost and temperatures, the quickest way in my opinion would be to tap into the manual defrost switch (MDS) inputs (KA8 & KB8 - for the older ML2/ML2i controllers). Refer to Carrier's manuals (which contain wiring diagrams) you can download from Carrier's website. Hopefully the ML3 still recognizes these manual defrost inputs as the ML3 can replace a ML2i controller. For reading temperatures, if your PLC can support temperature sensors, then installing separate sensors would be the quickest option.

The better but more complicated option: The MicroLink 3 (ML3) controller has a serial port which can communicate to your PC if you have the DataLine software. You can also download the latest Service pack 8 from Carrier's site (You'll need DataLine first though). If you're not bad at programming you can interface your PLC to the MicroLink directly but you'll need to figure out the communications protocol.

If you get desperate I'll try my best to find a better solution for you. Good luck.

[dglaab]

Thanks, Ill start with that. we have pretty good programming assets, if I can get the software, we can probably make it all work. Ill update somewhere down the line.........

Dan

[carrier_trained]

Hi guys:

I have 4 carrier elite and thinline shipping container units rnning a holding room here. I would really like to intergrate their electronics with my plant plc so I could do things like initiate defrosts from it, and monitor them. Does anyone have any access to or ideas on either electrical schematics or interface programs for this?

thanks

Dan

The software to communicate with carrier container units(DataLINE), you have to purchase from carrier container dealer, its proprietry software and comes with license key, it costs $480 here in aust, i just purchased mine last week, if you do buy it, update it to SP8.

[reefermechanic]

Reefer mechanic,

welcome to RE and nice to have a new member who are more than willing to help and share his knowledge.

regards,

...........

[phil Landon]

hi there Reeferman, Iam am currently working on an old mitsubishi CPE53-2BAIIIPU container. have just finished replacing the main display board and now get 2 alarm codes that won't clear. they are 207 and 356. I am starting to look at the main relay board (P-MGC05) I have all clean voltage going to the board and the pahse sequence seems ok. The alarms tell me that the 207 is single phase and the 356 alarm is the current sensor. As far as I can see they all originate from the above mentioned board.

any help would be very much appreciated as the customer wants to rent the box out over the Xmas period

thanks for your time

[reefermechanic]

Hi London

I have never seen CPE53-2BAIIIPU container.I don't know how is its??But if you send a picture and wiring diagram of reefer unit maybe i can help you..

I m waiting your kindly informations of reefer unit.

best regards.

reefer mechanic...

[phil Landon]

hi there reeferman , thanks for the reply. The mitsi box is now sorted. I did a factory reset with the dip switches on the main board (switches 6&7-moved them to the on position and powered up the container, then shut down and returned to the off position). I was told this by a guy who was an old hand at mitsi containers. this cleared the alarms that were hard latched in. I then proceeded to do a full PTI and the container passed. Thought this info might be handy to you and anyone else who may come across this problem

kind regards and happy holidays

[kaushi_k123]

hai,hope that u can help me on this.
i have got a 69 -nt carrier transicold container on which i have changed exp valve (hermatic type) 2 times,but still the container running on a vaccum suction pressure.what would be the problem.

[reefermechanic]

reefermechanic

[kaushi_k123]

this model has a stepper valve. i am running this container at -20 st pt. the problem is container pulls down to a temp around -9to -11 and not below.stepper valve shows 100% opening.i have replaced the compressor for this unit because the old one had a piston damage and the whole unit was contaminated.i also flushed the system with R-11 before installing the new compressor.

[Reefer tech]

reefer mechanic.. can you please help me find a manual for an SB 310 thermo king unit????
Thanks

[reefermechanic]

...........

[exxu]

Hello reefer mechanic
I have some problems with a ThermoKing CFIII M5.
This is the first container that i'm workink on, so, if you have some info (service manual, operation manual, etc),
please send it to danyelstoica@gmail.com.
Thank you very much.

[reefermechanic]

hi exxe

I did sen to e-mail to your mail adress.Check please than back to me..

See you

reefer mechanic

[Thein Htay]

Hi ,
I have one of daikin lxe10e-15a problem of frequently defrost 2 hours per time.Defrost setting is 99 hr at frozen mode . before in range , again defrosting. What is problem?
Thanks

[hhbbsun]

Hi reefer mechanic,

I am looking for one kind of integrated reefer machine (except TK, Carrier, Daikin, Mit) with genset and one or two sets of refrigrating system. If you know any, please kindly let me know. My email address is hongbin.sun@cimc.com.

Thank you for your help in advance.

Gary

[reefermechanic]

...........

[Andy Longhurst]

I fault with a TK sea container not controlling at set point +4 the liqiud line solenoid will not shut if you remove the coil the unit will pump down but it will not cut out on LP

[reefermechanic]

............