Supra 450, stupid plastic clips..

Hi all, has anyone else had probs with the plastic clip that keeps the spring attached to solenoid and throttle arm?
brand new clips and they still vibrate off, ive played with the alignment of solenoids, the height of throttle arm but nope, cable ties seem to work for now, i just dont like to rely on cable ties, is there a modded clip, ie not plastic?

Are they sprung eyes like the old one's?

sprung eyes? not quiet with you im affraid reeferjon, these here carriers are pretty new to me. Best way i can describe it is, this little plastic clip slots in the hole on solenoid and throttle arm and the spring slots into the plastic clip, said plastic clip then needs to be rotated round a bit so it holds it all together, sorry for crap explanation.. i think the older ones used brass clips? im unsure of this though.

Ahha, I got you so the old ones are not interchangable with new.

the old clips are not available anymore apparently, not that carriers are much help like, it seems unless you work for em they likes to keep their lips shut.

i will prolly have a go at my own mod, put a thread on the spring and use a nyloc to hold it all together, wont ever fall off then.
i hope...will keep here posted if i manage to sort something.

try Southern Sales & Service.
they are a good bet

good thinking, i gotta drop a compressor off to them this week so i will fire the question. :]
ta

Hi all, thought i'd keep this thread up instead of starting a new one.

Could anyone advise on a few things please, I would like to find out cro valve setting along with engine speed, high and low speed and also where do I take rpm reading from, clutch,flywheel front crank pulley?

As always, any help much appreciated.

Quote:

---

Originally Posted by alpha

Hi all, thought i'd keep this thread up instead of starting a new one.

Could anyone advise on a few things please, I would like to find out cro valve setting along with engine speed, high and low speed and also where do I take rpm reading from, clutch,flywheel front crank pulley?

As always, any help much appreciated.

---

Hi
Here's a cut and paste of the tec book ........check the engine speed at the front crank pulley.

The spring clips are ok if lub'ed from new.......if not...renew and start again.

have fun
Martin:)

SUPRA 450
Refrigerant Type/Charge - kg R404A / 3,2 kg

Diesel Cooling Capacity (-20?c / 0?c) - W 2580w / 4470w

Electric Cooling Capacity -20/0?C - W 2200w / 3590w

Heating Capacity (18/-18?c) - W -

Air Flow - m3/h 1610m3/h

Comp Oil Type EAL 68

Road Comp Type TM16

Road Comp Displacement - cc 163cc

Road Comp Capacity - ml 250ml

Stby Comp Type TM16

Stb Comp Displacement - cc 163cc

Stb Comp Capacity - ml 250ml

Engine CT2.29TV

Engine Displacement - cc 479cc

Oil Qty (by-pass) - ml 5,2 / 6,1 L

Coolant Capacity - ml 3,3 L

Low / High Speed - rpm 1800 / 2320

WaterT? / Oil Safety Switch - ?C 110°C/1 b

Valve Clearance - mm 0,145-0,185

mt frequency Yes

LRA - Amps 64A

MRA - Amps 9,1A

Alternator - Amps 50A

Battery Capacity - Ah 12v / 90Ah

Elec Power Consum at 0?C - W 3800w

Total Consum on Road 12/24 - W No

Total consumption on Stby 230 12/24 - A 15,8

Total Consumption on Stby 380 12/24 - A 9

Setting Air Switch - inch 0,65

Defrost Thermostat Open/Close - ?C 9 / 3°C

HP1 - bar 32 / 24

LP - bar - na

CPR - bar 1,8 b

TXV Orifice 3

Expansion Valve Superheat at 0?C - 8°C

Expansion valve Superheat at -20?C 7°C

LPP / HAPS Cut in / Cut out -

Quench Valve Opens/Closes - ?C 132°c

CDT - ?C No

Overload Relay Settings 380V - Amps 11

fantastic, cheers..:)