Activity Stream

Filter
Sort By Time Show
Recent Recent Popular Popular Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days All All Photos Photos Forum Forums Articles Articles Blog Blogs
  • RANGER1's Avatar
    03-05-2024, 11:14 PM
    RANGER1 replied to a thread Sabroe internal demister in Industrial Compressors
    cricri, To me just another possibility to reduce oil consumption. I think kit also includes oil from relief valve diverter. Obviously if...
    see more
    2 replies | 81 view(s)
  • josef's Avatar
    03-05-2024, 10:05 PM
    josef replied to a thread Sabroe internal demister in Industrial Compressors
    Dear cricri, don't have high expectations, after about 1000 hours of operation you have the problem back, please look for another way. Josef.
    see more
    2 replies | 81 view(s)
  • cricri's Avatar
    03-05-2024, 11:11 AM
    cricri started a thread Sabroe internal demister in Industrial Compressors
    Hello, Does anybody have an experience with this upgrade kit? thanks for reply
    see more
    2 replies | 81 view(s)
  • RANGER1's Avatar
    03-05-2024, 08:57 AM
    RANGER1 replied to a thread Ammonia Hose in NH3
    Just read your “lengthy “ post, very interesting. Stainless evaporative condensers could sufferer similar issues if not treated correctly. Once...
    see more
    12 replies | 773 view(s)
  • Tycho's Avatar
    02-05-2024, 11:41 PM
    Tycho replied to a thread Ammonia Hose in NH3
    Tell you what, pm me your address and I'll send you a 3 meter one :) we use the 1/2" hose, outside diameter, and we have 3/8 NPT female connection...
    see more
    12 replies | 773 view(s)
  • RANGER1's Avatar
    02-05-2024, 09:10 PM
    RANGER1 replied to a thread Ammonia Hose in NH3
    Tycho, Thanks might check out. Probably expensive, but the one we get are anyway.
    see more
    12 replies | 773 view(s)
  • Tycho's Avatar
    02-05-2024, 08:48 PM
    Tycho replied to a thread Ammonia Hose in NH3
    Seen as I haven't posted any videos in a while, Here's me playing with a 15 meter hose :) The supplier of this particular hose does a...
    see more
    12 replies | 773 view(s)
  • Tycho's Avatar
    02-05-2024, 05:38 PM
    Tycho replied to a thread Ammonia Hose in NH3
    they are corrugated on the outside but smooth on the inside, and coil up like a dream as they don't have a "memory" like the rubber hydraulic hoses....
    see more
    12 replies | 773 view(s)
  • Grizzly's Avatar
    02-05-2024, 01:36 PM
    Grizzly replied to a thread Mypro CPIV Controller Setpoint Selection in Electrical
    MP231. I have sent the controller Manual to you via your listed email address. hopefully you will get it. As to how to set it up I cannot advice....
    see more
    2 replies | 81 view(s)
  • AlexG's Avatar
    02-05-2024, 11:52 AM
    AlexG started a thread Daikin screw displacement in Commercial
    Hey guys! Anybody has a table with displacement of Daikin screw compressors? I need to know displacement (m³/h) of Fr3BS (HSA215)
    see more
    0 replies | 180 view(s)
  • RANGER1's Avatar
    02-05-2024, 09:25 AM
    RANGER1 replied to a thread Mypro CPIV Controller Setpoint Selection in Electrical
    MP231, Do you have a manual? Have you contacted Mycom in Sydney?
    see more
    2 replies | 81 view(s)
  • MP231's Avatar
    01-05-2024, 11:01 PM
    MP231 started a thread Mypro CPIV Controller Setpoint Selection in Electrical
    Hi, We have a customer who has an older Mypro CPIV controller on a compressor. The customer wishes to run the compressor as a swing machine where...
    see more
    2 replies | 81 view(s)
  • Grizzly's Avatar
    01-05-2024, 09:46 PM
    Grizzly replied to a thread Airedale UCCU70SQ-2/1 will not run in Industrial
    Hi Guys. Its possible that I have added the same link twice. Whereas I intended to show the end 2 pages of the Manual where the Circuit terminals are...
    see more
    2 replies | 128 view(s)
  • Grizzly's Avatar
    01-05-2024, 05:18 PM
    Grizzly replied to a thread Airedale UCCU70SQ-2/1 will not run in Industrial
    Hi Kirky. sorry about the delay. I assume you reset the alarms. its been a while since I last posted any links. Hopefully they work? ...
    see more
    2 replies | 128 view(s)
  • Kirky's Avatar
    01-05-2024, 10:02 AM
    Kirky started a thread Airedale UCCU70SQ-2/1 will not run in Industrial
    Hi all, Been called to a airedale UCCU70SQ-2/1 on 407c which will not start. There isn't any active alarms. The indoor temperature is high enough...
    see more
    2 replies | 128 view(s)
  • seanf's Avatar
    30-04-2024, 05:40 PM
    seanf replied to a thread Ammonia Hose in NH3
    Looks like you can get smooth bore, but also smooth bore exturnally convoluted to help with hose kinks. ...
    see more
    12 replies | 773 view(s)
  • RANGER1's Avatar
    30-04-2024, 09:07 AM
    RANGER1 replied to a thread Ammonia Hose in NH3
    Tycho, Out of interest can you roll these up easily to fit in service vehicle? Thought they may be at risk of kinking.
    see more
    12 replies | 773 view(s)
  • Tycho's Avatar
    30-04-2024, 06:52 AM
    Tycho replied to a thread Ammonia Hose in NH3
    We used to use hydraulic hoses, but they were heavy and would leak over time to form blisters on the outer skin. That's when we learned we could get...
    see more
    12 replies | 773 view(s)
  • seanf's Avatar
    29-04-2024, 05:58 PM
    seanf replied to a thread Ammonia Hose in NH3
    Cheers Ranger
    see more
    12 replies | 773 view(s)
More Activity