I need all your helps. F62WBH MYCOM of mine broken

[avico]

Hu hu hu....

Help me pls...

I have 02 new MYCOM comp. Model F62WBH

Oil pump fault, then all parts inside was broken
CAN I buy spares of WB model to REPLACE for WBH model ???
Could AnyOne answer me please !!!?
It's so URGENTLY. It's just 02 times of starting, then....

[INKYMART123]

we get our spares for mycom compressors from comtec 01215587757 try them

[avico]

we get our spares for mycom compressors from comtec 01215587757 try them

Dear INKYMART123

i can't found COMTEC website also their contact
Pls help me!!!


AND

I also want to know: CAN I USE F62WB'S SPARES FOR F62WBH MODEL ??????

[RANGER1]

Most parts are the same like pistons , valves , big end bearings .
Seal , main , thrust bearing , oil pump are different .

There must be a Mycom ( Mayekawa ) agent somewhere near you !

What damage do you have ?

[Toosh]

Hu hu hu....

Help me pls...

I have 02 new MYCOM comp. Model F62WBH

Oil pump fault, then all parts inside was broken
CAN I buy spares of WB model to REPLACE for WBH model ???
Could AnyOne answer me please !!!?
It's so URGENTLY. It's just 02 times of starting, then....

Try here

Vietnam
　Hochiminh Room 305, 3FL, Tuoi Tre Tower, 60A Hoang Van Thu, Ward9, Phu Nhuan Dist., Ho Chi Minh City, Vietnam TEL:
FAX: (84)8-3997-5284
(84)8-3997-5287 Its Mycom

Toosh

[avico]

Most parts are the same like pistons , valves , big end bearings .
Seal , main , thrust bearing , oil pump are different .

There must be a Mycom ( Mayekawa ) agent somewhere near you !

What damage do you have ?


@ RANGER1
Thanks for your informations
Could you pls listed here all differences between WB and WBH ( Also WA and WAH ...). Thanks so much!!

The oil pump and oil pressure swicth are fault, so ac ac ac ......all parts inside compressor was broken



Try here

Vietnam
　Hochiminh Room 305, 3FL, Tuoi Tre Tower, 60A Hoang Van Thu, Ward9, Phu Nhuan Dist., Ho Chi Minh City, Vietnam TEL:
FAX: (84)8-3997-5284
(84)8-3997-5287 Its Mycom

Toosh


@ Toosh

I also contact MYCOM Vietnam, but they're only Sale office, they sell comp. and Unit, NOT sell spares, AND can not get technicals help from them


DEAR ALL

Pls advice me, tell me where can i got MYCOM origin parts and also have fully technic help.

Thanks!

[Magoo]

If everything inside busted, your quickest and cheapest option is replace the whole compressor.
magoo

[Toosh]

@ RANGER1
Thanks for your informations
Could you pls listed here all differences between WB and WBH ( Also WA and WAH ...). Thanks so much!!

The oil pump and oil pressure swicth are fault, so ac ac ac ......all parts inside compressor was broken





@ Toosh

I also contact MYCOM Vietnam, but they're only Sale office, they sell comp. and Unit, NOT sell spares, AND can not get technicals help from them


DEAR ALL

Pls advice me, tell me where can i got MYCOM origin parts and also have fully technic help.

Thanks!

Try this one

http://mycomasia.com/contact.html

[la461]

Hu hu hu....

Help me pls...

I have 02 new MYCOM comp. Model F62WBH

Oil pump fault, then all parts inside was broken
CAN I buy spares of WB model to REPLACE for WBH model ???
Could AnyOne answer me please !!!?
It's so URGENTLY. It's just 02 times of starting, then....

What are you using the compressor for refrigeration or gas compression? I have worked on Mycom recip compressors a long time and don't remember the H designation. It usually means high pressure duty. High pressure compressors have needle bearings on all the wrist pins instead of only on the high stage pistons. catastrophic failures are liquid or oil pressure related. Compound compressors tend to have problems with the inter-cooling between the stages causing the high stage pistons being slugged(too cold) or starved and running hot causing the plates to break which allows re-compression super heating. Before i would risk a new compressor i would look at the package and check everything. Are there any undamaged parts? The crank can be turned and install over sized rod inserts .015'' or .030'' over.

[avico]

If everything inside busted, your quickest and cheapest option is replace the whole compressor.
magoo

Dear Magoo

Yes, it's the BEST WAY
But, about technical side. I still want to know, CAN we use WB spares for WBH model ???
And, what parts same, what parts different ????


Try this one

[]mycomasia]

Dear Toosh

I also already try this contact, but have no reply now


What are you using the compressor for refrigeration or gas compression? I have worked on Mycom recip compressors a long time and don't remember the H designation. It usually means high pressure duty. High pressure compressors have needle bearings on all the wrist pins instead of only on the high stage pistons. catastrophic failures are liquid or oil pressure related. Compound compressors tend to have problems with the inter-cooling between the stages causing the high stage pistons being slugged(too cold) or starved and running hot causing the plates to break which allows re-compression super heating. Before i would risk a new compressor i would look at the package and check everything. Are there any undamaged parts? The crank can be turned and install over sized rod inserts .015'' or .030'' over.

Dear la461

This comp. using in Freezing Vacuum system (-45oC) - Fresh Vegetable and Fruit factory

I have check ev'rything OK, Only Oilpump fault first, so bearing half, mechanic shaft seal, double shaft seal, main bearing DAMAGED

[charlie n]

Try Mycom office in Shanghai. email is ailsa-wong@mayekawachina.com.cn or weichen@mayekawachina.com.cn.
Basically, the WBH machine is a newer version of the WB. Many parts are the same but most bottom end parts are different.

[avico]

Try Mycom office in Shanghai. email is ailsa-wong@mayekawachina.com.cn or weichen@mayekawachina.com.cn.
Basically, the WBH machine is a newer version of the WB. Many parts are the same but most bottom end parts are different.

Thanks Charlie
I'll try this contact
Maybe they can help me solve problem

[mayekawa]

Mayekawa Singapore Pte. Ltd.
6 Tagore Lane Singapore 787470
Tel: (65) 6451-1565 / Fax: (65) 6451-4932

Mayekawa Mfg. Co., Ltd. (Vietnam) (nga@mayekawa.vn)
Tel: (84) 8-825-6917 / Fax: (84) 8-825-6919

[mbc]

if you could not find it inform me I have second hand of that in my work shop.

[avico]

if you could not find it inform me I have second hand of that in my work shop.


Dear mbc,

I still need it
Pls tell me your email address
Will send you the list of parts

or

Could you pls take some photos then email me: info@avico.com.vn]

Thanks much

Dang Anh Tuan
AVICO HVAC/R CENTER