Results 1 to 8 of 8
Thread: cleaning trane cond.
-
02-12-2001, 05:47 AM #1
cleaning trane cond.
anybody know of a good way to clean the condensers on the new trane units that have those "fuzzy" fins. besides pouring lighter fluid on them and burning them off! we use chemical cleaner and a pressure washer to clean everthing else but it folds over those "fuzzy" fins and packs them together. any other ideas?
-
04-12-2001, 10:48 PM #2
Re: cleaning trane cond.
Originally posted by aaron crimmins
We use chemical cleaner and a pressure washer to clean everthing else but it folds over those "fuzzy" fins and packs them together. any other ideas?
How about using the clemical cleaner in a LOW pressure sprayer instead of the HIGH pressure washer.
Or could you stand about 100 feet away from the coil when using the high pressure one.Brian - Newton Abbot, Devon, UK
Retired March 2015
-
05-12-2001, 05:57 AM #3
we use a foaming chemical cleaner such as "hydrocoil" whis is applied diluted - strength according to level of contamination - with a low pressure spray. Once the stuff has finished foaming and removing the dirt we just give the condenser a rinse with clean water, again using a low pressure spray and the job is done!
-
05-12-2001, 06:00 AM #4
When they are real dirty, I usually have more success blowing water from the inside of the coil towards the outside. Pull a condenser fan out and reach inside with a spray nozzle on a water hose. Worst case -- wash them out as described and then use chemical. Then hope they keep them cleaner from now on.
-
09-12-2001, 04:05 PM #5
thanks for the info. guys i talked to trane and they tell me that these new fins are designed to run a lower head when they get dirty comparied to the common fins out there. i think i'll try and keep them clean though!
-
11-12-2001, 07:52 PM #6
How does that work then - a lower head when the coil is dirty?
Seems like a really good invention!
-
23-05-2002, 09:34 PM #7
I have a nozzle that has several different stream ports. It is on a 4' tube with a cut-off near the hose attatchment. You clean from the inside-out without killing your back. No bending over and you can still watch the water come out. Spray till the water comes out clean. Chemical cleaners are overrated in my book.
-
10-06-2002, 11:20 AM #8
The fins are called spine fin and have been around for years. They tend to trap pollen alot more than the straight type fin but do disipate heat over a larger area and therefore use less aluminum (cheaper). they clean easily with Nubrite foaming cleanser we usually cut it 50/50 and spray from the inside out and it comes out easily. also tell the customer when they cut the grass to temporaily shut off the units and they will stay cleaner longer.
My wife says I don't listen to her....or something like that....
Similar Threads
-
Trane CGCE207 Problems
By AWCarillion in forum Trouble ShootingReplies: 12Last Post: 21-08-2011, 09:01 PM -
Trane RTAD125 Problems
By Latte in forum Trouble ShootingReplies: 10Last Post: 10-05-2010, 11:38 AM -
Are Trane Expensive
By frank in forum Air ConditioningReplies: 17Last Post: 20-05-2009, 01:55 PM -
Trane HP Defrost Board Problem
By FastEd in forum Heat PumpsReplies: 8Last Post: 05-09-2008, 01:30 AM -
Trane Filters
By Abe in forum CommercialReplies: 7Last Post: 30-09-2004, 08:40 AM