Results 1 to 10 of 10
-
07-02-2012, 08:53 PM #1
Mitsubishi City Multi PURY-P300 Condenser Coil
Hi people,
Just on the off chance that anybody on here has done it before...
I am in the process of removing a condenser coil (heat exchanger in Mitsi language) on a Mitsubishi 'City Multi' on R410a.
Its obviously quite a new unit but the copper passes have split at the bottom of the coil caused by either liquid hammer or vibration.
Where do you start? Is it a case of just slowly removing access panels or is there a certain process in which panels to remove first?
I have google'd this on the off chance there may be a pdf file from Mitsi in the form of an exploded diagram or some kind of assembly plan.
I am lucky enough to have been on the two day 'City Multi' course but the two operation manuals and A4 binders we were given don't shed any light on this.
I know I'm clutching at straws but thought I'd post on here to see if anybody could shed any light on this, before I go back to site.
feedback greatly appreciated.
-
07-02-2012, 09:07 PM #2
Re: Mitsubishi City Multi PURY-P300 Condenser Coil
Top off ,fan deck off, front off ,back off ,sides off.
Well that's how I do it .
Done a few ,you'll need a side kick to give you a hand.
You'll get an exploded view in the spare parts manual if you have it.Don't have one to hand.
Cheers
StuTool's ? check ! Condom's ? check !
If you can't fix it , f*ck it !!!
-
07-02-2012, 09:57 PM #3
Re: Mitsubishi City Multi PURY-P300 Condenser Coil
pretty much as stu said, ive only a couple but they come apart pretty easily,
Kev
-
07-02-2012, 10:02 PM #4
Re: Mitsubishi City Multi PURY-P300 Condenser Coil
take ur time, remove all coil.pipe thermistors and dont overheat the end stubbs-good luck- and enjoy ur trip to the scrap yard
-
07-02-2012, 11:12 PM #5
Re: Mitsubishi City Multi PURY-P300 Condenser Coil
Thankful of the feedback gents, much appreciated!! Scrap yard was a must, but had trackers fitted in vehicles last week + doubt it would fit in car!!! Thanks again
-
08-02-2012, 01:08 AM #6
Re: Mitsubishi City Multi PURY-P300 Condenser Coil
Just take note of advises from Stufus and IM
PURY.jpg
-
08-02-2012, 07:10 AM #7
Re: Mitsubishi City Multi PURY-P300 Condenser Coil
Ace photo! Cheers very much for that!
-
08-02-2012, 07:38 PM #8
Re: Mitsubishi City Multi PURY-P300 Condenser Coil
trackers- when u park up on site- unplug it and leave it on the floor- it has battery back up for 8 hrs- once youve visited the recycling ctr return to site and carefully plug ur tracker black box into the lil connector- be carefull not to bend the pins- othrwise an £80 tamper fee applies- if its fleet smart-make sure u have black duct tape or coloured cable ties from rs as they like to try and prevent this-ps lead round the gps ariel doesnt work-ive tried!- or plan b check for an app for scrap yard locations-or get the apprentice to carry it
-
08-02-2012, 08:50 PM #9
Re: Mitsubishi City Multi PURY-P300 Condenser Coil
Had a tracker in the van but i eated it
http://t1.gstatic.com/images?q=tbn:A...olDlBRmXl0WLQwMostly found in Oxfordshire, UK :)
-
08-02-2012, 10:06 PM #10