New Carell Control Panel

[Abe]

I put in the new design Master Cella Carell Electronic Control panel today,

Yes, it looks cool and its sauve.........gone into a spanking new Cellrtherm cold room

It has a built in isolator switch as well

Question I have is...........The manual is terrible. The writing is small..........has anyone understood how to program the parametres, how to access the parameters.

Im switching on tomorrow. I connected the cold room to the auxiliary relay no 2, as it says in manual.

When i press the light switch , nothing happens.

When I press the standby switch.........nothing happens.....!!

grrrrrrrrrrrrrrrrr

If some member has recently used this controller, pse help.

I bought it from Hawco...........

[Brian_UK]

Download the manual from here...
http://www.carel.com/carelcom/web/en...=5&id_gamma=15

Text is readable on screen (zoomed)

File is 1.16mb

[Abe]

Thanks Brian

Printed it out.
Still feel its been written in Greek

[Brian_UK]

Still feel its been written in Greek

Aren't they all ?
No offence to the Greeks by the way

[Peter_1]

Only now seen your post Abe.
We have some 5 Master Cella's installed last months, so if any problems, fire your questions Abe.
But, my son knows them better then I do

[Abe]

I got it all working, it looks good.

The light is connected to AUX relay 2, to switch the light on you keep the button pressed for 5 secs.............then it switches!!

The programming part , I managed, only wished that the manual would explain the sequences better, in a flow chart, instead of having to squint reading small print.....

Peter.

I say I managed to set the parametres, to gain access to set parameters you press prg and set simultaneosly for 5 secs.

Then it shows 00 on screen

You press up /down buttons until you reash password which is 22.

Then you press SET.....

Now you can change settings

First is, HACCP which are the probe parameters, which I dont touch

I wanted to go to modify the next set, which are COMPRESSOR

Its got all the stuff in the manual, but its small and not clear cut. The sequence should be in big bold and in flow chart form.

The sequence is I think.

scroll
When you reach the desired parameter
Press SET

At this stage I gave up..............because the manual gets all muddled up..............

I will write it up later this evening so u understand what I mean



This is where I was having difficulty.

[Abe]

Heres a pic of the controller and room
Just showing off my new casio digital camera!!

[Temprite]

G'day Abe.

This is the sheet I use for Carel controllers.

It is written in Australian, might be harder to understand than Greek

[Abe]

Temp

I cant see it

[Temprite]

Sorry Abe.

This might be a bit better.

[Temprite]

No thats not any better either...

Well it is a handy sheet when it can be read

Cant seem to resize the picture big enough to read.

Sorry Abe.

[Abe]

its ok Temp

No worries mate
Brian sent me a very useful link which I have printed off

Thanks for helping anyways

[vinyljedi]

hi first time ive used this system but i have one problem. in the manual the time for defrost says 8 ORE, can ne1 please explain wat ORE stands for
cheers

[nike123]

hi first time ive used this system but i have one problem. in the manual the time for defrost says 8 ORE, can ne1 please explain wat ORE stands for
cheers

Ore is Italian word for Hour!

[nick clark]

hi have had same problem , wired into aux 2 , but but still no light , what par have to be set at for light
nick

[nick clark]

hi nick again ,light is on all the time except on defrost ?

[Peter_1]

Vinyljedi, thanks Nike123.
Will this be your only post here, even no introduction?

[nick clark]

hi again , realy do need help , handing over tomorrow , and yes feel dum , simple light not working
regards nick from a wet cornwall

[Brian_UK]

Nick Clark, a specific question might get an answer.

So far you said that the light won't switch on, then you stated that it is on all the time except during defrost.

We don't know what you want so I'm sorry it is difficult to answer.

[greyhound]

I got it all working, it looks good.

The light is connected to AUX relay 2, to switch the light on you keep the button pressed for 5 secs.............then it switches!!

The programming part , I managed, only wished that the manual would explain the sequences better, in a flow chart, instead of having to squint reading small print.....

Peter.

I say I managed to set the parametres, to gain access to set parameters you press prg and set simultaneosly for 5 secs.

Then it shows 00 on screen

You press up /down buttons until you reash password which is 22.

Then you press SET.....

Now you can change settings

First is, HACCP which are the probe parameters, which I dont touch

I wanted to go to modify the next set, which are COMPRESSOR

Its got all the stuff in the manual, but its small and not clear cut. The sequence should be in big bold and in flow chart form.

The sequence is I think.

scroll
When you reach the desired parameter
Press SET

At this stage I gave up..............because the manual gets all muddled up..............

I will write it up later this evening so u understand what I mean



This is where I was having difficulty.

next time use a peco expert.it is clear and simple.and does exactly what it says on the tin.