Results 1 to 8 of 8
  1. #1
    Join Date
    Feb 2015
    Location
    Pakistan
    Age
    47
    Posts
    67
    Rep Power
    10

    Aluminium Evaporator coil for Ammonia



    Hi

    This has been discussed before, but I don't know results obtained in end.
    http://www.refrigeration-engineer.co...orator-for-NH3

    Question is same: Is it good idea to build Aluminium Evaporator for ammonia operation.

    Some technicians says that Aluminium is more corrosive when gas pass from Aluminium pipes.

    Has someone installed it? What's the experience.

    Regards
    Salman



  2. #2
    Brian_UK's Avatar
    Brian_UK is offline Moderator I am starting to push the Mods: of RE Site Moderator : and general nice guy
    Join Date
    Mar 2001
    Location
    Dorset
    Age
    76
    Posts
    11,192
    Rep Power
    60

    Re: Aluminium Evaporator coil for Ammonia

    The thread that you have quoted has given good answers and has covered the question.
    Brian - Newton Abbot, Devon, UK
    Retired March 2015

  3. #3
    Join Date
    Feb 2015
    Location
    Pakistan
    Age
    47
    Posts
    67
    Rep Power
    10

    Re: Aluminium Evaporator coil for Ammonia

    Hi

    It was 2009, quite old now..
    Can someone share new experiences?

  4. #4
    Join Date
    Dec 2007
    Location
    australia
    Posts
    3,356
    Rep Power
    39

    Re: Aluminium Evaporator coil for Ammonia

    Quote Originally Posted by skhan855 View Post
    Hi

    It was 2009, quite old now..
    Can someone share new experiences?
    Nothing has changed since then, Ammonia is safe with aluminium, nothing left to say.
    Believe it to have very good heat transfer, next to using copper.

  5. #5
    Join Date
    Feb 2015
    Location
    Pakistan
    Age
    47
    Posts
    67
    Rep Power
    10

    Re: Aluminium Evaporator coil for Ammonia

    Hi

    Just to reconfirm, are we speaking about aluminium Pipes + Aluminium fins or just aluminium fins?

    My evaporator supplier is insisting that carbon steel pipes will have more life compare to ammonia,

  6. #6
    Join Date
    Dec 2007
    Location
    australia
    Posts
    3,356
    Rep Power
    39

    Re: Aluminium Evaporator coil for Ammonia

    Quote Originally Posted by skhan855 View Post
    Hi

    Just to reconfirm, are we speaking about aluminium Pipes + Aluminium fins or just aluminium fins?

    My evaporator supplier is insisting that carbon steel pipes will have more life compare to ammonia,
    That might be true, externally as stated in old post about pitting on outside of tube.
    Aluminium is fine with ammonia fins & tubes in direct contact with it.

  7. #7
    Join Date
    Dec 2007
    Location
    australia
    Posts
    3,356
    Rep Power
    39

    Re: Aluminium Evaporator coil for Ammonia

    This is one of a number of articles on aluminium & ammonia

    http://www.advancedfreezer.com/listings/files/73_1.pdf

  8. #8
    Join Date
    Mar 2009
    Location
    U.S.A.
    Posts
    320
    Rep Power
    20

    Re: Aluminium Evaporator coil for Ammonia

    All aluminum evaporators have been in use at least 40 years. They last very well in cold storage duty, for controlled atmosphere and similar storage, for plenty of dock operations and in process operations where they operate 24-7. Aluminum evaps lighter for same construction and nominally smaller because of the improved heat transfer: thus often save on structural. Some form of dielectric separation required between coil and (steel) pipe and aluminum much more active chemically than steel so refrigerant needs to be maintained in near-pure condition. They are more delicate than Galv Steel and there is no bridge in terms of contributed material between tube and fin so in "wet coil" duty the air cannot contain soluble corrosives or the fins will loose contact with the tube; this also true of Aluminum fins on Stainless tubes though the collection of reactives are different. Stainless fins on Stainless tubes tend not to do this but the heat transfer is worse and adding any profile to the fins is more difficult so ST-ST tends to become a large heavy coil with flat fin plates.
    Basically the selection is application driven by the nature of the space. Protein and dairy processors should be careful with aluminum in spaces involving washdown or otherwise chemical exposures.
    There are also some horror stories with internal chemical soups attacking aluminum from the inside but that was the result of some pretty odd refrigerant contamination conditions.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •