Results 1 to 14 of 14
Thread: Lennox package unit
-
20-12-2013, 07:44 PM #1
Lennox package unit
I have a Lennox kha 70 with aMerit® Series Thermostat 51M32
the unit runs ok in cooling but the 4way valve does not denergized
on heating.
any suggestions
cheers
-
20-12-2013, 08:41 PM #2
Re: Lennox package unit
Faulty PCB
The difference between genius and stupidity is that genius has its limits.
Marc
-
20-12-2013, 09:27 PM #3
Re: Lennox package unit
The wiring on the remote is r,b,c,g,o,y1,w1
and the outdoor has r,c,w1,y1,g,oc,w2,y2
R and c 24volts
y1 cooling
g-fan
w1 is heating but I think it's for electric heaters
not sure which one is for the 4way valve on heating
cheers
-
20-12-2013, 09:34 PM #4
-
20-12-2013, 09:41 PM #5
Re: Lennox package unit
No it's a Lennox kha 70
-
20-12-2013, 10:12 PM #6
Re: Lennox package unit
R 24v from transformer
C common
Y1 & Y2 cooling stages 1 & 2
G fan motor
W1 W2 is electric heater if fitted but sometimes O can also be for the 2nd stage electric heater.
I can't find a copy of the wiring diagram so can't see where the 4 way valve is wired into.
Can you not trace it back from the 4 way valve and see which terminal it comes from on the board?
Also from the model number I would say it is a heat pump but......are you sureThe difference between genius and stupidity is that genius has its limits.
Marc
-
20-12-2013, 10:40 PM #7
Re: Lennox package unit
http://www.lennoxcommercial.com/tech...ce-manuals.asp
cant upload service manual- but its at the bottom of the list
-
20-12-2013, 10:52 PM #8
Re: Lennox package unit
http://www.mediafire.com/view/prijxcdyq93d9as/0803a.pdf
service manual- damn mediafire had logged me out
-
21-12-2013, 01:49 PM #9
Re: Lennox package unit
Here is the outdoor package unit terminals .just not sure if oc is for the heating ie 4way valve
-
21-12-2013, 06:25 PM #10
Re: Lennox package unit
Based on document 0803a.pdf heat pump mode begins when energizes W1. See page 43. You can set a bridge between W1 and R for test WP mode.
-
21-12-2013, 07:40 PM #11
Re: Lennox package unit
Just looking through that manual ,reversing valve is circuit is broken when relay k8 is energised , so it must be wired through nc circuit on relay k8 ,if contacts on k8 are welded or 24 volt coil is shot reversing valve wouldnt de energise.Apologies if you already ruled this out
-
21-12-2013, 08:01 PM #12
Re: Lennox package unit
Also check defrost board
The difference between genius and stupidity is that genius has its limits.
Marc
-
21-12-2013, 08:46 PM #13
Re: Lennox package unit
Thermostat 51M32 is suitable for non-heat pump units. See source
http://www.lennox.com/pdfs/manuals/Lennox_Merit_Non-Programmable_Thermostats_Manual.pdf
-
22-12-2013, 09:30 PM #14
Re: Lennox package unit
I was looking at the manual for the 51m32. And o is for reverse valve on heating.i was talking to a Lennox engineer and he told me to wire o on the remote to w1 on the package unit but this still didn't work.ill have a better look at unit after Christmas .just left the 4aay valve pluged off the board to let the client have heating over the holidays.