thermoking container manuals

[jamcool]

Have a CFII thermoking unit,anyone has a manual i could use,here is the thing.
All the writings on the control is missing have now was of knowing what is what,HELP!!!!!!

[ewart]

Jamcool you may need to post a photo of this unit.
Ewart

[Reeferjon]

Hi WHich model is it, what controller...do you have a BM number

[ewart]

the BM number is 090171 and the serial number is 0324350730, this is jamcool using ewarts log in

[Reeferjon]

OK, no luck with the BM or S/No...
Its a CFII what model should be M something from 4 to 40....can you identify the controller model

[jamcool]

i see M19.3 as model number the thing is unit still icing back to the suction line,the charge has not changed read the sensors,coil 3670 ohms,return 3290 ohms,and discharge 3310 ohms I think those are ok,it has 9 relays on it K1 to K9 would like to know which control what also any manuals or wiring drawings that can be found.
ANY HELP WOULD BE GOOD
jamcool

[canunez]

I have a CFII unit and I am looking for a manual. Did you ever find yours? Can you help me?

[Reeferjon]

please contact me off list.
JOhn.

[WBSERVICEFTW]

Help,

Does Anyone Out There Have A Service / Operations Manual For A Thermo King Cfii M37.
Container Unit. Or Know Where We Might Be Able To Find One. Any Help Would Be Greatly Appreciated....thanks

[REEFER-TEK]

I have a full library collection of all makes and models of TK and CTC units in PDF.

I would like to complete my collection with a Deltec Vector and X2 manual if anyone has any of these in PDF to share or email that would be very cool.

If anyone here is looking for anything I probably have it. Including software wintrac 4.6, reefer manager, SR2 diagnostic tester rev3, ibox 5308, dataview dos, optiset 3.26 rev and way to many more to name off here.

Regards R-T

[clivemtk]

how old is the version of reefer manager

[Rodolfo Plata]

I have a full library collection of all makes and models of TK and CTC units in PDF.

I would like to complete my collection with a Deltec Vector and X2 manual if anyone has any of these in PDF to share or email that would be very cool.

If anyone here is looking for anything I probably have it. Including software wintrac 4.6, reefer manager, SR2 diagnostic tester rev3, ibox 5308, dataview dos, optiset 3.26 rev and way to many more to name off here.

Regards R-T

____________

Would you have among your collection a XMT thermo king service manual? Unbelievably, We have one of those unit still operating.
Regards,
R. Plata

[lsinc1]

I have a full library collection of all makes and models of TK and CTC units in PDF.

I would like to complete my collection with a Deltec Vector and X2 manual if anyone has any of these in PDF to share or email that would be very cool.

If anyone here is looking for anything I probably have it. Including software wintrac 4.6, reefer manager, SR2 diagnostic tester rev3, ibox 5308, dataview dos, optiset 3.26 rev and way to many more to name off here.

Regards R-T

Hi,

Is the wintrac software avaiable for download? If so could you send me a link?

Thank you
Tony

[Bermejol]

I have a full library collection of all makes and models of TK and CTC units in PDF.

I would like to complete my collection with a Deltec Vector and X2 manual if anyone has any of these in PDF to share or email that would be very cool.

If anyone here is looking for anything I probably have it. Including software wintrac 4.6, reefer manager, SR2 diagnostic tester rev3, ibox 5308, dataview dos, optiset 3.26 rev and way to many more to name off here.

Regards R-T

Hi all, I am new here. I am needing all information possible for the Thermo King V-500, MD I And MD II SR.
thanks for your support.
Thanks and good luck.

[xtremeoption]

kindly sennd me link. Many thanks

I have a full library collection of all makes and models of TK and CTC units in PDF.

If anyone here is looking for anything I probably have it. Including software wintrac 4.6, reefer manager, SR2 diagnostic tester rev3, ibox 5308, dataview dos, optiset 3.26 rev and way to many more to name off here.

Regards R-T

[metricwrench]

How do I contact you? I need help(manual)
wrench

I have a full library collection of all makes and models of TK and CTC units in PDF.

I would like to complete my collection with a Deltec Vector and X2 manual if anyone has any of these in PDF to share or email that would be very cool.

If anyone here is looking for anything I probably have it. Including software wintrac 4.6, reefer manager, SR2 diagnostic tester rev3, ibox 5308, dataview dos, optiset 3.26 rev and way to many more to name off here.

Regards R-T

[metricwrench]

How do I contact you? I need help(manual)
wrench

If I add an email address, would that help?
thanks
wrench====== shadow@harleydeals.net

[HTL10]

Hi. I saw your quote and i was wondering if there is anyway you can send me a download of WinTrac 4.6, Refer Manager, Sr2 diagnostic tester rev3. I been trying to get it forever so i would be glad happy. if you can't then it's ok. Thank. please reply

Hai

I have a full library collection of all makes and models of TK and CTC units in PDF.

I would like to complete my collection with a Deltec Vector and X2 manual if anyone has any of these in PDF to share or email that would be very cool.

If anyone here is looking for anything I probably have it. Including software wintrac 4.6, reefer manager, SR2 diagnostic tester rev3, ibox 5308, dataview dos, optiset 3.26 rev and way to many more to name off here.

Regards R-T

[andreiortan]

Hello i have o TK SL200 unit and i whood need software wintrac 4.6 from you.if you could send me wintrac.thanks my email is andreiortan@yahoo.com

[abbsnowman]

Ok, everyone please stop asking for manuals. This is not a library it is a classroom. Offer something before you ask for something. Maybe then we may help?

[bruisermac]

i agree with abbs...first time ever..hahahaha...post a new thread with specific needs so it doesnt get so confusing!!!

to answer the original question about flooding or iced up suction line we need more info like box temp etc... as long as the compressor is not iced up your ok cause the cfII with open drive and x430 compressors have a throttling valve to prevent damage to the compressor. on the M35 units sometimes you may get frost to the compressor body depends on the conditions inside etc...

hope this helps.

[greg_haun2000]

Hey Folks, i'm new to forum. Working on trans reefers in Afghanistan for the troops. need pdf service manual for thermo king mod# CRR-40-800E Ser# A001082207. don,t have much access to any info here in this dustbowl. any help would be great! Thanks, Greg

[GregDogCO]

I'm new to this site. I have an I-box but need help communicating with it. In some posts I've read about wintrac flash s/w and other means of communicting with data loggers but not sure how it fits together. Does wintrac s/w run on pc but also need some flash files for proper communication? I'd appreciate any advice and help getting wintrac s/w too. Thanks.

[zanman]

yes we have them- i can fax you what you might need?

[C Bagtas]

Hi,
just try to check the suction trottle valve or the 3 way valve,before that is i found in our unit,our unit is refrigeration van that we use in aircraft.

[spool25]

Hello Guys,

I am also looking for Thermo King manuals. The two manuals I am looking for are

Parts Manual for SB-III 30 SR+
Maintenance Manual SB-III 30 & 50
SR+ µP-IV+

[tariqenng]

i need thrmoking mechecal rfigertion dia gram any one have please dend me

[tariqenng]

any one who can tell me about refigertion cyecal about thrmo king

[Thermoking.kong]

have you tried a thermoking dealer
you will need the unit serial number

also this site wont allow me to mail it to you as its 23 mb

[tariqenng]

is anyone have service manuals of xmt thrmoking

[thermo prince]

Hi Tariq Engg.

Are you working for transport company or a service agent there? XMT is an old generation nosemount truck freezer unit from 1970's - early 80's powered by either Onan or Wisconsin gasoline engines.
Abbar in Jeddah and Riyadh may be able to help with manuals and parts.
Some countries 'repower' these with Yanmar or Kubota diesels and continue to run them today.
If Abbar cannot help w/ parts contact me offline. There's a warehouse nearby me where a large inventory of old hard to find parts for XMt, XKW.XRW and NWD stocked.

Its not a 'Container' unit or Reefer unit like CF11/CSR/CRR as fitted on 20'/ 40' ISO ocean going boxes.

Spool 25 - which part of USA do you work and likewise are you working with owner/transport or a repair company?
Did you try local agent or MPLS Hq for these? If you are an owner or in the trade, they would be happy to oblige I'm sure.

[pedrefer]

We have a box with XMT-50 now operating as a stationary unit removed from road chasis, powered by 3 phase 230 volt.

I am Looking for a manual and any information in retrofiting to R134a.

[absolute-zero]

We have a box with XMT-50 now operating as a stationary unit removed from road chasis, powered by 3 phase 230 volt.

I am Looking for a manual and any information in retrofiting to R134a.

Hi pedrefer,

I see your new here to RE, welcome aboard.

Why not convert the sytem to (MP66 R401b). The cooling capacity is better and the sytem is more forgiven to this basic conversion.

[paulo almeida]

go to web site o fdupon and the have refrigerant for conver direc, not need oil poe

best regards

[absolute-zero]

go to web site o fdupon and the have refrigerant for conver direc, not need oil poe

best regards

http://www.refrigerants.dupont.com/S.../suvamp66.html

[Big John]

TP. dont forget that some xmt units had tukomski engines fitted. I think they were for the US market.we used to get a few in jeddah...

[SKOOBY]

Yes i agree MP66 is the way to go.May have manual will let you know

[micki_kp]

I am looking for a wiring diagram for a thermo king some dummy took the wiring harness out of the unit before they were ready to replace it. any help would be grately appreciated.

thermo king
model sll-38 max
b.m
092039
serial # 0518819091
ref
r502 16 lbs
thank you in advance.

[Hummer]

I'm looking for a refrigeration circuit diagram for a SB-310+ or similar unit with an electronic throttling valve.

[utc/tk foreman]

there are so many cf-II units produced, with so many small differences, that you really do need the specific model number to have the right wiring diagram and fix the unit properly.

[biopetro]

Hello everyone,

I recently bought a used Thermoking CGII M-22 15kw generator. But the controller was toasted due to corrosion could someone help me with a manual for this unit?

Thanks,

TD

[utc/tk foreman]

Hello everyone,

I recently bought a used Thermoking CGII M-22 15kw generator. But the controller was toasted due to corrosion could someone help me with a manual for this unit?

Thanks,

TD

I think i have a manual, but you prob wont need it. Those boards are really one of the only problems you see with those gens. It corrodes slightly from the box letting moisture in and then it burns itself. I can almost guarantee if you put a new board in it, it will fire up and work fine.

[fabio-zinpao]

Hello folks!
I need the MP3000 controller manual and the electric diagram. I appreciate if anyone could help me.

[HTL10]

My email is Haitle10@yahoo.com

[Seban]

Can you send the manuals at pasqual@poczta.onet.pl

[birnahaf]

Can you send the manuals at birnahaf@gmail.com

thanx so much!

[pulper]

Need manual for MD-ii SR 1998.With the

μ

P-T

MICROPROCESSOR
futuresinger1@gmail.com
thank you so much please send if ya have.

[khaos_unleashed]

Hello all I also would like any thermo king manuals available just started work for a refrigerated single axle box truck rental company with various models any help would be greatly appreciated. m.morris2008@yahoo.com

[agiouto]

Good morning.Please i want the manuals from Thermoking reefer container model Magnum 924

[agiouto]

Good morning.Please i want the manuals from Termoking reefer container model Magnum 924.

reefercontainer@hol.gr