Results 1 to 7 of 7
  1. #1
    Join Date
    Apr 2001
    Location
    UK
    Posts
    2,119
    Rep Power
    26

    How do you check a thermistor?



    Air conditioners have thermistors all over controlling the different parts.....

    I would appreciate if anyone can advise how to check them. I know we have to check the resistance across the terminals.


    Any opinions, statements and facts expressed in this message do not constitute legal advice in any shape or form and is given for a general outlook in nature. You are advised to seek appropriate and specific professional assistance from a regulated and authorised advisor for definitive advice.

  2. #2
    Join Date
    Dec 2004
    Location
    Australia
    Age
    52
    Posts
    519
    Rep Power
    20

    Re: How do you check a thermistor?

    Hello Aiyub.

    Different a/c manufacturers use different value thermistors with their units.

    You need information from the manufacturer of the resistance at certain temps for the thermistors used on their units.

    Make a slurry of ice and water in a cup place the thermistor in this and check on the charts resistance at 0 deg c.

    You could use a thermometer in a glass of water alongside the thermistor.

    In my experience they usually open circuit.

    (Especially when someones dog chews it off the side of the unit.)

  3. #3
    Join Date
    Aug 2001
    Location
    UK
    Posts
    1,058
    Rep Power
    24

    Re: How do you check a thermistor?

    Thermistors used in AC systems are NTC devices (negative temperature Co-efficient) this means that the temperature and resistance are inverse to each other. It is never a linear value, so you will need in each case the manufacturer?s co-efficient chart or table. It should be in their manuals

    Some use the same value gradient for all the sensors on their machines, but don?t assume that they all do.

    Sensors have a centre value. Usually this is the resistance at a fixed temperature as a reference. For example 25 degrees at 10kohm. But it could vary according to the sensor range.

    To check one you need to take two or three accurate readings of temperature against resistance along the curve.
    You definitely need a good electronic thermometer and a good Multimeter.

    If there is any variance, ditch the sensor. Usually the values are more compressed at the lower temperature end and this is where you need the greatest accuracy.

    Some sensors have a habit of being erratic due to water getting through the seal.
    ________
    glass bongs
    Last edited by Argus; 07-02-2011 at 09:23 AM.

  4. #4
    Join Date
    Oct 2001
    Location
    Nottingham UK
    Posts
    5,733
    Rep Power
    51

    Re: How do you check a thermistor?

    Another good tip is to take a reading at the given(ambient) temp, say 20C and see how that relates to the manufacturers chart. With the meter connected, hold the thermister (to warm it up) and watch your meter to see if it responds as per the chart. When the thermister stops warming (at around 30C), you should get a feeling if it is responding correctly or erratically.

    You do need the chart though no matter how you test the sensor (unless it is open circuit or short circuit )

  5. #5
    Join Date
    Sep 2011
    Location
    USA
    Age
    38
    Posts
    6
    Rep Power
    0

    Re: How do you check a thermistor?

    If I'm not mistaken, thermistors have no polarity so if you check the current/volts/resistance using the ohms formulas you can pretty well nail the resistance to a "T" using a good thermometer and multi meter.

    Check the I, R and V going to the thermistor. Remove the thermistor (probably shouldn't run the A/C while it's not connected), and check the resistance through the terminator at different temperatures. You can probably get a rough quadratic equation (non-linear change over temperature fluctuations) and apply the ohms formulas to determine how the resistance effects current and voltage drops across the thermostat. It's a whole lot more math, but if you don't have the tech specs, it can be done I believe.

  6. #6
    Join Date
    Sep 2011
    Location
    USA
    Age
    38
    Posts
    6
    Rep Power
    0

    Re: How do you check a thermistor?

    Auto correct on iPhone changed thermistors to "terminator" and "thermostat". Hope that clears things up...

  7. #7
    Join Date
    Apr 2006
    Location
    UK
    Age
    55
    Posts
    1,920
    Rep Power
    29

    Re: How do you check a thermistor?

    Quote Originally Posted by TimH View Post
    (probably shouldn't run the A/C while it's not connected) it can be done I believe.
    Timothy

    twice in one day... your hilarious...Thankyou

    R's chillerman
    If the World did not Suck, We would all fall off !

Similar Threads

  1. Daikin fault codes
    By Chris2005 in forum Air Conditioning
    Replies: 45
    Last Post: 21-03-2012, 11:09 PM
  2. air cooler uneven distribution check
    By Lc_shi in forum Fundamentals
    Replies: 5
    Last Post: 17-06-2006, 12:47 AM
  3. Air conditioning maintenance procedure
    By Andy T in forum Air Conditioning
    Replies: 12
    Last Post: 27-05-2006, 06:57 PM
  4. Double check needed
    By Latte in forum Trouble Shooting
    Replies: 14
    Last Post: 11-08-2004, 12:46 PM
  5. Compressor Check for locked rotor voltage
    By shogun7 in forum Trouble Shooting
    Replies: 0
    Last Post: 04-04-2004, 12:44 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •