Results 1 to 8 of 8
Thread: Fujitsu indoor unit removal
-
09-10-2010, 11:48 PM #1
Fujitsu indoor unit removal
Hi all -
I need the repaint the walls in a room with an indoor unit (ASTA09LFC) for a Fujitsu heat pump system.
What would be involved in taking down the indoor unit so that I can repaint? I'm a qualified electrical engineer, so that side of things isn't an issue, but what about the pipes going to the outdoor unit? Is it effectively a sealed unit where the indoor unit can't be removed without remedial installation work anyway? And what's the procedure for removal anyway?
If anyone could give me some pointers it'd be very much appreciated.
I don't know who originally installed the system, and as much as I'm sure an installer would do a great job, I could really do without having to pay someone a few hundred dollars just to repaint the walls!
Thanks very much
Tawny
-
10-10-2010, 04:19 PM #2
Re: Fujitsu indoor unit removal
hi tawny,
well if you know the person who fitted it originally, why not give them a ring and get a price?
-
10-10-2010, 08:00 PM #3
-
10-10-2010, 08:49 PM #4
Re: Fujitsu indoor unit removal
If it's just for decorating purposes, why do you need to remove the indoor fan coil?
When the wall is painted and then the fan coil is re-fitted, you won't see the wall behind the fan coil anyway?
Seems like an un-necessary expense to me.
-
10-10-2010, 08:58 PM #5
Re: Fujitsu indoor unit removal
hi tawny,
no your not missing something obvious, its just that to the untrained person there are LOTS of pitfalls to the simple job of removing the indoor unit
loosing gas
getting air in the system
getting moister in the system
getting blown off the ladder by an explosion of gas
getting badly burned by the gas
being a skilled man you know that you are capable of doing a very good job at most other trades, but this one is,nt something that can be learned as you go along< apolagies for missquoting you earlier<
-
10-10-2010, 09:38 PM #6
Re: Fujitsu indoor unit removal
Hi Tawny,
As Frank says, there is no need to remove the unit completely from the wall.
Turn off the power to the system, open the filter access panel and remove the filters.
You should see two or three screws above the air outlet slot which secure the plastic cover to the base unit.
Undo and remove the screws; have a look at the top of the casing and also along the bottom of the casing. You should see some plastic locating clips which when released will allow the outer plastic cover to be removed.
You should now have the base unit left on the wall and if you use a small paintbrush you can paint right up to the framework of the unit. The plastic cover overlaps the base frame so everything will look OK when it is refitted.
If you need a user manual for the unit then click here..
http://www.fujitsugeneral.com.au/pro...247/asta09lfc/Brian - Newton Abbot, Devon, UK
Retired March 2015
-
11-10-2010, 09:26 AM #7
-
11-10-2010, 08:54 PM #8
Re: Fujitsu indoor unit removal
^^ You're very welcome, now then - the green paint on the website needs a touch up here and there, what are you doing over the weekend?
Brian - Newton Abbot, Devon, UK
Retired March 2015
Similar Threads
-
Fujitsu AOY90TPAMF
By andy c in forum Heat PumpsReplies: 6Last Post: 08-02-2010, 04:22 PM -
Removal of Fujitsu A/C Condensor
By NikoG in forum Air ConditioningReplies: 2Last Post: 09-07-2009, 07:01 PM -
Removal of Fujitsu A/C Condensor
By NikoG in forum DomesticReplies: 0Last Post: 09-07-2009, 04:16 PM -
fujitsu wall mount volt free relay
By mike live in forum Air ConditioningReplies: 3Last Post: 09-04-2009, 08:26 PM -
Fujitsu air con fitting
By airconlad in forum Air ConditioningReplies: 8Last Post: 03-09-2008, 09:03 PM