Results 1 to 8 of 8
Thread: Danfoss KVL valves.
-
22-09-2010, 03:29 PM #1
Danfoss KVL valves.
Hi.
Just as a matter of interest.
Has anyone had any problems with the Danfoss KVL12 crankcase pressure regulating valve running with R404a, leaking or sticking?
I have had a few give these problems in Zanotti stradle fridge units, and I have now seen that Zanotti are using the Sporlan CRO6 in their new equipment!!.
Regards.
*****don.
-
22-09-2010, 07:32 PM #2
Re: Danfoss KVL valves.
I had one some months ago, a Danfoss KVL
It's better to keep your mouth shut and give the impression that you're stupid than to open it and remove all doubt.
-
22-09-2010, 08:21 PM #3
Re: Danfoss KVL valves.
Do they stick open or closed?
Jon
-
22-09-2010, 10:52 PM #4
Re: Danfoss KVL valves.
mine remained sticked in a certain position after pressurizing the system while searching for a leak.
It's better to keep your mouth shut and give the impression that you're stupid than to open it and remove all doubt.
-
23-09-2010, 03:22 PM #5
Re: Danfoss KVL valves.
Hi Jon.
The ones we have had problems with have tended to stick shut, or just leak out through the adjusting screw.
Don.
-
23-09-2010, 05:46 PM #6
Re: Danfoss KVL valves.
I was just wondering as a Zannoti unit i put a new comp on seemed to have a lower than expected suction pressure but i can never tell with cap tube systems, they always run lower than i would think!
-
24-09-2010, 09:53 AM #7
Re: Danfoss KVL valves.
Any reason for the loss of the compressor?
If not I would have a check of the valve, I am asuming that the unit you repaired has one fitted.
I have one on test at the presrent, at -20 sucction is about 5 psig, which is about 10 psig lower than I would expect, but seems to be running ok.
We use them for dual temp, so I am going to let it warm up and run it on the chill setting soon, let you know what I get latter.
Don.
-
24-09-2010, 04:50 PM #8
Re: Danfoss KVL valves.
The start relay had burnt out where the neutrals all connect up, (it had suffered a similar burn about a year ago) put a new relay and capacitors on and it lasted a week before it failed.
I am planning to cut the old one open and see whats gone wrong with it, but i suspect its electrical rather than mechanical.
The new one was running about 15/18 psi on R404A and i think the room was at -12/14c.
Similar Threads
-
Danfoss Solenoid Valves
By ice_cold in forum CommercialReplies: 4Last Post: 15-12-2009, 04:57 AM -
Too dependent on Danfoss Valves
By kelvin_27_84 in forum IndustrialReplies: 8Last Post: 24-01-2009, 08:33 PM -
Danfoss EKC315a ETX Valves
By LesClem in forum Technical DiscussionsReplies: 2Last Post: 14-12-2006, 11:26 PM -
Danfoss AKV10 valves
By David PS in forum FundamentalsReplies: 18Last Post: 28-07-2006, 03:56 AM -
Danfoss AKV Valves
By Budokan in forum Supermarket RefrigerationReplies: 8Last Post: 05-04-2004, 07:20 PM