Results 1 to 7 of 7
  1. #1
    Join Date
    Nov 2004
    Location
    China
    Posts
    176
    Rep Power
    20

    Carrier Brine Chiller



    My Company is buying a used Carrier 30GT-190 chiller that we want to used as a rink chiller for temporary outdoor rinks. The manuals I can find refer to a low LCWT limit of 1.7 degrees and a "factory modification" to permit operation down to -9.4 LCWT. Does anyone know how to reset this limit so we can run down below 1.7?



  2. #2
    Brian_UK's Avatar
    Brian_UK is offline Moderator I am starting to push the Mods: of RE Site Moderator : and general nice guy
    Join Date
    Mar 2001
    Location
    Dorset
    Age
    76
    Posts
    11,025
    Rep Power
    60

    Re: Carrier Brine Chiller

    Sorry, can only find 30GTN documents on this Carrier site...

    http://eto.carrier.com/lit.asp
    Brian - Newton Abbot, Devon, UK
    Retired March 2015

  3. #3
    Join Date
    May 2009
    Location
    Sydney
    Posts
    73
    Rep Power
    15

    Re: Carrier Brine Chiller

    Brine selection is via dip switch setting however may require EXV change due to being over capacity at lower suction pressure.

  4. #4
    Join Date
    Nov 2004
    Location
    China
    Posts
    176
    Rep Power
    20

    Re: Carrier Brine Chiller

    Thanks for the help guys. We may have to use "percussive maintenance" to get it to work but I hope we can find the correct solution.

  5. #5
    Join Date
    Sep 2007
    Location
    Somerset
    Age
    69
    Posts
    4,698
    Rep Power
    46

    Re: Carrier Brine Chiller

    Hi Charlie.
    Is this the old type with the Flowtronic Control system?
    I so, as you state Carrier say that Factory Mods are required.
    Normally access to these has to be with the Carrier software.
    Although I did work with an ex Carrier Engineer a couple of years ago.
    Who accessed the controls and reset the expansion valve control parameters.
    (Without the Software)

    I suspect this is what Gregd is refering to above.
    I think this mod is not for the faint hearted.
    I may still have some hard copy details archived.
    Sadly I have not got anything in pdf format.
    If you can get hold of someone from Carrier or that is ex Carrier.
    That may be your answer?

    Good Luck Grizzly

  6. #6
    Join Date
    Nov 2004
    Location
    China
    Posts
    176
    Rep Power
    20

    Re: Carrier Brine Chiller

    My people have been talking to Carrier in China but they don't seem to know anything about the system. It was imported some time ago so, as I understand, it has the old Flowtronic control system that Grizzly is referring to.

  7. #7
    forest ou's Avatar
    forest ou Guest

    Re: Carrier Brine Chiller

    Hi, buddy. I am sales on brine chillers from China . to my experience , you just ask the Carrier company for the maintenance code. you incode it in the touch screen. and you can reset your data there. normally. the protection point is 5C lower than the working temperature . just like . if you need lowest outlet is -10C, you can set the protection point to be -15C.

    Hope it make sense to you.

Similar Threads

  1. Replies: 12
    Last Post: 27-03-2011, 04:12 AM
  2. Carrier chiller basic board problem
    By noushad123 in forum Trouble Shooting
    Replies: 25
    Last Post: 17-06-2010, 06:55 AM
  3. Can’t get a brine chiller down to temperature.
    By dkemper in forum Trouble Shooting
    Replies: 8
    Last Post: 08-06-2007, 03:38 PM
  4. Carrier Chiller Help
    By superswill in forum Trouble Shooting
    Replies: 7
    Last Post: 18-01-2007, 10:06 PM
  5. Carrier chiller oil migration
    By lowtech in forum Industrial
    Replies: 5
    Last Post: 30-04-2006, 04:11 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •