Results 1 to 16 of 16
Thread: welding whit nitrogen
-
27-07-2009, 05:48 PM #1
welding whit nitrogen
Hey Guys (and girls),
just wondered how you good folks set up the nitrogen equipment before and during the actual welding.
i connect the nitrogen hose on one end of the line,and connect a second hose on the other end of the line that needs welding.
than i keep the end of the second hose in a bottle of water and open the nitrogentank just enough to when there are bubles in the waterbottle.
thats tells me there is a constant flow,and also if the nitrogen tank is empty.
its cheap,but works fine for me.
Ice
-
27-07-2009, 06:21 PM #2
Re: welding whit nitrogen
Not sure i would be dipping hoses in water, i normally connect it to one end, wind the reg upto about 50PSi, then used a hose with a tap on it, open it enought to allow a little flow (you can hear the flow at the other end and or lick you finger and hold it at the end and you will feel it) and weld. leave the OFN flowing while i cool the joint then off with the OFN and seal both ends!
-
27-07-2009, 09:25 PM #3
Re: welding whit nitrogen
would'nt use water bottle either jst attach hose to pressure regulater,turn handle,i either hold hose to my ear or feel with my hand for desired pressure. all done safely of course.
-
27-07-2009, 10:16 PM #4
Re: welding whit nitrogen
Ive got one of those gas flow thingies with a bead in a glass tube, the more flow (adjustable with a knob) the higher the bead goes, same as used on a mig/tig welder. was only about £20
-
28-07-2009, 08:03 AM #5
Re: welding whit nitrogen
Last edited by Peter_1; 28-07-2009 at 09:04 AM.
It's better to keep your mouth shut and give the impression that you're stupid than to open it and remove all doubt.
-
28-07-2009, 01:26 PM #6
Re: welding whit nitrogen
regulator and flow meter otherwise you can forget about the adaptor sitting with bottle pressure(suicide fitting)been there done that
mmm to beer or not to beer...........lets drink breakfast
-
28-07-2009, 05:20 PM #7
Re: welding whit nitrogen
when i connect the hose to the nitrogen tank,i have a pressure regulator in between. and if i let the other end in the plastic bottle,the hose is about 5mtr long. so capillarity of H²O is out of the question. i did check t out the consumption Peter_1, and at the moment my system is cheaper on nitrogen. and i am also sure that there is always a constant flow, i notice directly when the NGO tank is empty.
Ice
-
28-07-2009, 07:06 PM #8
-
28-07-2009, 10:01 PM #9
Re: welding whit nitrogen
Both have a pressure reducer but a pressure regulator regulates the outlet to a certain pressure (psi of bar which you don't need for soldering) and a flow regulates for a certain flow (l/min)
Both look similar (analog dials) but the working principle isn't.
As soon you blank of, a flow regulator will stop where a pressure will build up. A flow of 5 to 10 l/min is enough.
What I mean with a spill: we needed the first exams 1 bottle OFN for every 3 brazing tests with pressure type. Now we can +/- 7 exams with 1 one bottle with a flow type. The flow type is even obligated for the exam centers now in Belgium when you do the brazing tests.
TIG welders always use a flow type.It's better to keep your mouth shut and give the impression that you're stupid than to open it and remove all doubt.
-
28-07-2009, 10:34 PM #10
Re: welding whit nitrogen
Mines like AR-101-2, you can set the flow by how high the bead goes in the tube.
Jon
-
29-07-2009, 02:49 PM #11
Re: welding whit nitrogen
I keep an assortment of mostly clear plastic tubes (hoses) in a milkcrate with all my nitro goodies. I slide a tube on the one end and clamp it with a springclamp. It holds on by itself for light flow, and blows off with too much flow. Since, I've been doing this, I've noticed much less nitrogen use. Works for me!!!
Wally
-
29-07-2009, 11:13 PM #12
Re: welding whit nitrogen
Can I ask what welding we're talking about here? Is this ordinary pipe brazing?
www.compactaircon.co.uk
-
10-09-2009, 09:33 PM #13
Re: welding whit nitrogen
Hi,
I am a new member and I would ask that how the liquified nitrogen gas preserved without being empty
Thanks
I need
-
10-09-2009, 10:29 PM #14
-
10-09-2009, 10:29 PM #15
-
04-10-2010, 02:43 AM #16
Re: welding whit nitrogen
we installed a new walk in freezer w/404a. line set is about 8 feet long from cond to evap w/ about 12 joints brazed . after about 3 hrs the txv shut down i told the tech it might b from not using nitro while brazing all the pipe. dpoes anyone agree with me????
Similar Threads
-
brazing under nitrogen
By cool#9 in forum Air ConditioningReplies: 5Last Post: 24-10-2010, 08:30 AM -
Ultra compact water cooler for Tig Welding?
By bjamesw in forum FundamentalsReplies: 7Last Post: 28-12-2008, 03:04 PM -
Nitrogen Condensing by Temperarture
By Reflexive in forum Technical DiscussionsReplies: 0Last Post: 21-12-2008, 12:23 AM -
Nitrogen purging?
By monkey spanners in forum Tools and CalculatorsReplies: 5Last Post: 10-06-2007, 09:47 PM -
Nitrogen freezer
By Peter_1 in forum IndustrialReplies: 11Last Post: 05-10-2005, 05:04 PM