Results 1 to 9 of 9
Thread: Vallient gyser thread #2
-
22-11-2007, 10:27 PM #1
VIP Poster
- Join Date
- Apr 2006
- Location
- Not so sunny coast (BC Canada)
- Age
- 41
- Posts
- 1,620
- Rep Power
- 23
Vallient gyser thread #2
What voltage thermopile does it use, I need a new one for my instent gase water heater but unsure if it uses a 15mV or 30mV couple.
Any help will be realy apreciated one of you guys new the piping for it, I'm still loving you for the help!
-
22-11-2007, 11:38 PM #2
Moderator
I am starting to push the Mods: of RE Site Moderator : and general nice guy
- Join Date
- Mar 2001
- Location
- Dorset
- Age
- 76
- Posts
- 11,025
- Rep Power
- 60
Re: Vallient gyser thread #2
Wouldn't really know MG but assuming that the cost is not great why not buy one of each?
Brian - Newton Abbot, Devon, UK
Retired March 2015
-
23-11-2007, 11:12 PM #3
VIP Poster
I am starting to push the Mods: of RE
- Join Date
- Aug 2003
- Location
- Netherlands
- Age
- 49
- Posts
- 620
- Rep Power
- 21
Re: Vallient gyser thread #2
What type was it again? Don't remember anymore, it's been a while back!
-
24-11-2007, 03:28 AM #4
VIP Poster
- Join Date
- Apr 2006
- Location
- Not so sunny coast (BC Canada)
- Age
- 41
- Posts
- 1,620
- Rep Power
- 23
Re: Vallient gyser thread #2
http://www.refrigeration-engineer.co...ead.php?t=7633
Unit is: MAG 125/7 TZ PB
-
25-11-2007, 12:21 AM #5
VIP Poster
I am starting to push the Mods: of RE
- Join Date
- Aug 2003
- Location
- Netherlands
- Age
- 49
- Posts
- 620
- Rep Power
- 21
Re: Vallient gyser thread #2
The manual doesn't say which one either, so my best bet is to get to the local plumber and maybe he can help you!
-
26-11-2007, 01:50 AM #6
VIP Poster
- Join Date
- Apr 2006
- Location
- Not so sunny coast (BC Canada)
- Age
- 41
- Posts
- 1,620
- Rep Power
- 23
Re: Vallient gyser thread #2
Not around here lucky if they even know they exist, all they know is pay day is friday and sh*t flows down hill around most parts here.
-
26-11-2007, 10:59 PM #7
VIP Poster
I am starting to push the Mods: of RE
- Join Date
- Aug 2003
- Location
- Netherlands
- Age
- 49
- Posts
- 620
- Rep Power
- 21
Re: Vallient gyser thread #2
I'll try a mate tomorrow and see if he knows, he used to work for Vaillant.
-
26-11-2007, 11:48 PM #8
VIP Poster
- Join Date
- Jan 2003
- Location
- Crewe, United Kingdom
- Age
- 58
- Posts
- 723
- Rep Power
- 22
Re: Vallient gyser thread #2
Should be 30 mV
Karl
-
27-11-2007, 12:48 AM #9
VIP Poster
- Join Date
- Apr 2006
- Location
- Not so sunny coast (BC Canada)
- Age
- 41
- Posts
- 1,620
- Rep Power
- 23
Re: Vallient gyser thread #2
Awsome thank you guys so much! It is a beuty full little thing but hard as hell to get all the details to properly recondition it and I'm going to keep all the info on a file for any one ells around these parts with the same!
