View Full Version : New Carell Control Panel
I put in the new design Master Cella Carell Electronic Control panel today,
Yes, it looks cool and its sauve.........gone into a spanking new Cellrtherm cold room
It has a built in isolator switch as well
Question I have is...........The manual is terrible. The writing is small..........has anyone understood how to program the parametres, how to access the parameters.
Im switching on tomorrow. I connected the cold room to the auxiliary relay no 2, as it says in manual.
When i press the light switch , nothing happens.
When I press the standby switch.........nothing happens.....!!
grrrrrrrrrrrrrrrrr
If some member has recently used this controller, pse help.
I bought it from Hawco...........
:)
Brian_UK
12-08-2006, 11:14 PM
Download the manual from here...
http://www.carel.com/carelcom/web/eng/catalogo/prodotto_docs.jsp?id_prodotto=163&id_tipologia=5&id_gamma=15
Text is readable on screen (zoomed)
File is 1.16mb
Thanks Brian
Printed it out.
Still feel its been written in Greek
:D
Brian_UK
13-08-2006, 02:20 PM
Still feel its been written in Greek
:DAren't they all ?
No offence to the Greeks by the way:)
Peter_1
14-08-2006, 07:37 AM
Only now seen your post Abe.
We have some 5 Master Cella's installed last months, so if any problems, fire your questions Abe.
But, my son knows them better then I do ;)
I got it all working, it looks good.
The light is connected to AUX relay 2, to switch the light on you keep the button pressed for 5 secs.............then it switches!!
The programming part , I managed, only wished that the manual would explain the sequences better, in a flow chart, instead of having to squint reading small print.....
Peter.
I say I managed to set the parametres, to gain access to set parameters you press prg and set simultaneosly for 5 secs.
Then it shows 00 on screen
You press up /down buttons until you reash password which is 22.
Then you press SET.....
Now you can change settings
First is, HACCP which are the probe parameters, which I dont touch
I wanted to go to modify the next set, which are COMPRESSOR
Its got all the stuff in the manual, but its small and not clear cut. The sequence should be in big bold and in flow chart form.
The sequence is I think.
scroll
When you reach the desired parameter
Press SET
At this stage I gave up..............because the manual gets all muddled up..............
I will write it up later this evening so u understand what I mean
:(
This is where I was having difficulty.
Heres a pic of the controller and room
Just showing off my new casio digital camera!!
Temprite
20-08-2006, 08:20 AM
G'day Abe.
This is the sheet I use for Carel controllers.
It is written in Australian, might be harder to understand than Greek:D
Temprite
20-08-2006, 12:18 PM
Sorry Abe.
This might be a bit better.
Temprite
20-08-2006, 12:24 PM
No thats not any better either...
Well it is a handy sheet when it can be read:rolleyes:
Cant seem to resize the picture big enough to read.
Sorry Abe.
its ok Temp
No worries mate
Brian sent me a very useful link which I have printed off
Thanks for helping anyways
vinyljedi
27-02-2008, 01:47 AM
hi first time ive used this system but i have one problem. in the manual the time for defrost says 8 ORE, can ne1 please explain wat ORE stands for
cheers
nike123
27-02-2008, 11:24 AM
hi first time ive used this system but i have one problem. in the manual the time for defrost says 8 ORE, can ne1 please explain wat ORE stands for
cheers
Ore is Italian word for Hour!
nick clark
06-07-2008, 06:18 PM
hi have had same problem , wired into aux 2 , but but still no light , what par have to be set at for light
nick
nick clark
06-07-2008, 06:19 PM
hi nick again ,light is on all the time except on defrost ?
Peter_1
06-07-2008, 06:34 PM
Vinyljedi, thanks Nike123.
Will this be your only post here, even no introduction?
nick clark
06-07-2008, 06:46 PM
hi again , realy do need help , handing over tomorrow , and yes feel dum , simple light not working
regards nick from a wet cornwall
Brian_UK
06-07-2008, 11:17 PM
Nick Clark, a specific question might get an answer.
So far you said that the light won't switch on, then you stated that it is on all the time except during defrost.
We don't know what you want so I'm sorry it is difficult to answer.
greyhound
19-09-2008, 12:08 PM
I got it all working, it looks good.
The light is connected to AUX relay 2, to switch the light on you keep the button pressed for 5 secs.............then it switches!!
The programming part , I managed, only wished that the manual would explain the sequences better, in a flow chart, instead of having to squint reading small print.....
Peter.
I say I managed to set the parametres, to gain access to set parameters you press prg and set simultaneosly for 5 secs.
Then it shows 00 on screen
You press up /down buttons until you reash password which is 22.
Then you press SET.....
Now you can change settings
First is, HACCP which are the probe parameters, which I dont touch
I wanted to go to modify the next set, which are COMPRESSOR
Its got all the stuff in the manual, but its small and not clear cut. The sequence should be in big bold and in flow chart form.
The sequence is I think.
scroll
When you reach the desired parameter
Press SET
At this stage I gave up..............because the manual gets all muddled up..............
I will write it up later this evening so u understand what I mean
:(
This is where I was having difficulty.
next time use a peco expert.it is clear and simple.and does exactly what it says on the tin.
Powered by vBulletin® Version 4.2.1 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.