PDA

View Full Version : Fan blade puller UK







TrickyRikki
15-09-2017, 04:48 PM
Hello everyone,

i was wondering if anyone could possibly point me in the right direction on where to get a fan blade remover tool in the UK.

i found plenty in USA with ridiculous postage costs i cant seem to find anything to remove fan blades in the UK.

Any names of such tools here would be appreciated.

Thanks

Rik

FaultCode
15-09-2017, 05:58 PM
Try searching/Googling for "pulley puller", sold by just about everyone.

cadwaladr
15-09-2017, 06:09 PM
What type of fan is it,is it on the condenser or evaporator

TrickyRikki
15-09-2017, 06:18 PM
What type of fan is it,is it on the condenser or evaporator

was just an in general question mate, usually with the condenser motors though.

Thanks FaultCode i will try pulley puller instead of fan blade remover, thank you

Rik

cadwaladr
15-09-2017, 06:31 PM
Normally the motors are scrapped so I take the motor off cut through the shaft dose it in wd then drive it out with a punch on a vice or over a deep reach socket works everything for me.

TrickyRikki
15-09-2017, 07:18 PM
Normally the motors are scrapped so I take the motor off cut through the shaft dose it in wd then drive it out with a punch on a vice or over a deep reach socket works everything for me.

yeah i know what you mean but ive been on a few sites where we've reused the fan so cutting it off the shaft and hammering it out is not always possible on site, i saw some vids on youtube where people used a fan blade remover and i thought it looked alot easier, but when i searched it all i got was american tools but after doing what FaultCode said i found loads of them.

Thanks for both your help and advice though

Rik

Rob White
15-09-2017, 07:21 PM
.

https://www.machinemart.co.uk/p/clarke-4-inch-3-jaw-gear-puller-cht607/?da=1&TC=GS-040210607&gclid=EAIaIQobChMIxPH6_Oan1gIVBLvtCh0eXw1DEAQYAiABEgKW9PD_BwE

Machine Mart 12

Rob

.

TrickyRikki
15-09-2017, 08:40 PM
.

https://www.machinemart.co.uk/p/clarke-4-inch-3-jaw-gear-puller-cht607/?da=1&TC=GS-040210607&gclid=EAIaIQobChMIxPH6_Oan1gIVBLvtCh0eXw1DEAQYAiABEgKW9PD_BwE

Machine Mart 12

Rob

.

Thanks Rob this is the ones i was looking at

Thanks for everyones help much appreciated

Rik

FaultCode
15-09-2017, 08:56 PM
Just be very careful if they have plastic hubs.

Lots of wd40 and a fair few prayers to your god.

TrickyRikki
15-09-2017, 09:19 PM
Just be very careful if they have plastic hubs.

Lots of wd40 and a fair few prayers to your god.

Lol thanks for the advice i will bear that in mind.

Rik

monkey spanners
15-09-2017, 10:55 PM
I got one on ebay, just had to pay the shipping and tax from the USA, had it for seven years or so so have forgotten what it cost but still find it useful.

https://www.youtube.com/watch?v=Gy6MmNbw-2c

TrickyRikki
16-09-2017, 02:07 PM
I got one on ebay, just had to pay the shipping and tax from the USA, had it for seven years or so so have forgotten what it cost but still find it useful.

https://www.youtube.com/watch?v=Gy6MmNbw-2c

Ah yeah i have seen that one on ebay, wasnt sure if it was any good?

Thanks for the link ive already seen that i been subbed to you for a while lol

Rik