PDA

View Full Version : Panasonic Fault codes





ronaldo9
25-03-2006, 11:47 PM
Hey everyone,

I really hope someone can help, im looking for fault codes for a panasonic a/c system. The serial number on the outdoor unit is CU-140C53XP and the error codes are F15 and F41 . What a nightmare panasonics website offers no support for this unit.. help

Brian_UK
26-03-2006, 12:42 AM
Hi Ronald, welcome to the forum.

Likewise I couldn't find your model on the Panasonic site, did you get to this page---
http://www.panasonic.com/consumer_electronics/bp_split_ac/manuals.asp

there might be a similar control setup on one of those; might be worth a look.

Temprite
26-03-2006, 04:23 AM
Hey everyone,

I really hope someone can help, im looking for fault codes for a panasonic a/c system. The serial number on the outdoor unit is CU-140C53XP and the error codes are F15 and F41 . What a nightmare panasonics website offers no support for this unit.. help

G'day Ronaldo

Have got a fault code list here may or may not be relevant to your unit.

F15=Drain level float switch problem.

F41= High pressure switch open circuit problem (3 LED's illuminated on outdoor PCB).
or
Low pressure sensor problem. (2 LED's illuminated on outdoor PCB).

Regards.

al
26-03-2006, 09:29 PM
Ronaldo,

ring walkair in dublin, ask for service dept,. they're really easy to deal with:)

014568070

Alec

MOUNIR COOLING
07-03-2007, 12:00 AM
hi
looking for sanyo inverter error code please. sure someone can help.

Brian_UK
07-03-2007, 12:15 AM
hi
looking for sanyo inverter error code please. sure someone can help.
Not under Panasonic I wouldn't think:confused:

Electrocoolman
07-03-2007, 12:30 AM
Mounir....start a new thread under Aircon....also have a search. What system SAP or SRW

ECM

wkwong.alan
14-10-2007, 12:24 PM
G'day Ronaldo

Have got a fault code list here may or may not be relevant to your unit.

F15=Drain level float switch problem.

F41= High pressure switch open circuit problem (3 LED's illuminated on outdoor PCB).
or
Low pressure sensor problem. (2 LED's illuminated on outdoor PCB).

Regards. hello Temprite i got a problem in Panasonic ceiling casstle single spit unit my problem is fan coil and the condenser stop at the same time and the outdoor unit LED 2,3,5,7 light up so how to solve this problem?thanks in advance
Regards.

paul_h
17-10-2007, 10:45 AM
Should be current detect pcb faulty, or compressor drawing too much current.
I don't have your model a/c, but panasonic fault codes stay pretty much the same
Normally panasonics have this info on the inside of the access panel.
Plus fault codes from the indoor unit make it easier to look up.

if the compressor is running, check the amps and refrig pressures.

Hatchy
01-08-2008, 07:09 AM
I know this is a old thread but did someone have luck in locating service/install manual for Panasonic CU-140c53XP. I have one of those lovely jobs to help a neighbor install this system that he purchased at auction. I cant find any info on the capacity, etc other then model number. Regards

Sjonnie
03-09-2008, 02:32 PM
Hey all ... also got a Panasonic airconditioning here. It's got fault code F22, any idea what the Panasonic means?

paul_h
03-09-2008, 02:47 PM
Depends on the model. Conventional ducted, old split, newer inverter etc.
To be honest, I have a lot of panasonic fault codes and manuals, none of them have F22.
But if you have the model number, maybe someone can find it.

matt.yelland
27-02-2009, 11:08 PM
I came across a Panasonic unit today with an E9 Fault Code.

Indoor model number, CS-125U1HPP.

Outdoor model U-100H2SPP.

I spoke to Climate Tech and got a lot of info from them, 08705 218218

panaloni
29-06-2009, 03:21 PM
where can I get a service manual for a panasonic wall split model: cuw24dkr with indoor csw24dkr

paul_h
01-07-2009, 05:34 PM
Well being as that's a conventional unit, there's not a lot of useful info in the manual anyway. It's pretty much the same as every other conventional model service manual word for word.
What do you need to know?

ridwan
31-07-2009, 12:13 AM
hi paul,
panasonic cu-112c52hp out door unit,
do you know the fault code if42, even better if you have the fault code list.thanks

paul_h
31-07-2009, 05:07 AM
probably compressor current trip.
Is there nothing in the outdoor unit with fault codes?

oldgit
31-07-2009, 12:23 PM
That model is a Daikin/Panasonic unit. So the fault code will be the same as the Daikin codes.
From memory E9 was related to a Electronic Expansion valve fault.

oldgit
31-07-2009, 12:24 PM
That model is a Daikin/Panasonic unit. So the fault code will be the same as the Daikin codes.
From memory E9 was related to a Electronic Expansion valve fault.

Prince Vaillant
31-07-2009, 01:08 PM
Some panasonic non inverter fault codes

f15 - drain level float switch
f16 - louver switch
f17 - dc fan motor
f20 - indoor temperature sensor
f21 - pipe temp sensor (indoor)
f26 - remote control transmission
f27 - indoor outdoor unit disconnected
f30 - system problem
f31 - suction pressure protection
f32 - compressor overcurrent frotection
f40 - heat exchanger outlet temperature sensor
f41 - high pressure switch open circuit

frank
31-07-2009, 08:23 PM
Nice one Jay :)

JRMAIR
13-08-2010, 12:50 AM
HEY EVERYONE

Im looking fault codes for a panasonic inverter the model is CU-E12-EKU and the fault code is f93

stefs_cruiser
13-08-2010, 01:24 AM
F93 compressor abnormal revolution

Check compressor windings (all 3 windings should be the same)
check output from inverter with inverter checker

shaday
15-10-2010, 07:17 AM
I want know about error codes for panasonic inverter air-conditioner

stefs_cruiser
18-10-2010, 12:01 AM
Post the fault code,and model number, and we may be able to assists :-)

proudlock
01-11-2010, 09:37 AM
How you going, i have a cs-e18dkr with fault code H23, what does this mean, Thanks,
Rob

moondawn
01-11-2010, 07:58 PM
Indoor Pipe Sensor Faulty Sensor Disconnected, Faulty or Contacts Dirty


cheers lee

Gwyn
07-12-2010, 10:48 PM
Hi I have "F3" Fault code on Panasonic CU10ME1XPK
Any ideas please I think discharge sensor fault but what causes this they have been changed and still same fault :(

croc1774
13-12-2010, 03:37 PM
Panasonic Fault Codes Below....

http://www.mediafire.com/download.php?0f53eejjp271doa

Gwyn
14-12-2010, 12:14 AM
Many thanks I misled you with fault code sorry it should have been 'J3' this indicates a sensor fault I think?
The link is good but not for my model mine is CU-10 ME1XPK If you have got another link that would be great?

Thanks,

croc1774
14-12-2010, 12:33 AM
Many thanks I misled you with fault code sorry it should have been 'J3' this indicates a sensor fault I think?
The link is good but not for my model mine is CU-10 ME1XPK If you have got another link that would be great?

Thanks,

Yes you are right it is the indoor air sensor
Regards;)

HVACRSA
20-02-2011, 09:57 PM
Thanks guys!