Barker cabinet/coldstore controllers

[Silhouette]

Hi All,
Does anyone have any information on these controllers used in Morrisons etc. please?
I have done a search but not found much and the website is now Epta based and pretty much useless!
I used to work with these things 20+ years ago but have lost all the paperwork I had on them!

Thanks in anticipation :)

Mel

[richelli]

Which controller do you need info for?

[Ian_Eb]

I think I can lay my hands on the instruction sheets for most of them. Do you know which one or possibly even what store and I should be able to find it.

[Silhouette]

Hi Richelli/Ian_Eb,
I have been told that I will be involved in a few refits in the next couple of months and I'm just trying to make sure I have some info before arriving on site blind as it were!
I have no idea of the model numbers etc. but if you have anything at all I'd be greatfull if you could PM me and I'll let you have my email address.

Many thanks,
Mel.

[jjthefridge]

Hi, Have you tried jtl website, that's the controllers that are used in Morrison, or try ringing there help desk and they could point you in right direction. j.j.

[jjthefridge]

found something on laptop, for epta rdm mercury 6.5 any good????

[Ian_Eb]

Hi,

These will be the OCC / Universal controllers used by GB in the mid to late 90's.

The original boards are now replaced by the universal controllers. It has 2 bit switched to set its mode.

from memory you can have

TEV Controller - Case
EEV Controller - Case
EEV Controller - Coldroom
M&S Controller

the Storescan will speak to the normal controller modes but not the M&S one.

Once the group and section number are programmed you can get the controller online to the storescan and this will let you configure the setpoint etc. However, there may be some other settings that need to be done on the controller itself.

Defrosts are controlled from the panel and the group and section number will display under the case address in the case config page.

[Silhouette]

Thanks for the info fellas!
I have the JTL, RDM and CDK stuff but any actual GB paperwork eludes me!
Hey Ho! I shall try other lines of communication to see what they come up with!

Regards,
Mel.

[spacemanmark]

I think we have some old folders in the office Mel, I will have a look and let you know.

Hope you are well mate

Mark

[tony--1]

think iv got what your after will post later

[Ian_Eb]

Tried to post these but get told they are too large for the forum.

http://www.filedropper.com/occ15

http://www.filedropper.com/occ17

http://www.filedropper.com/occ22

http://www.filedropper.com/occ23

http://www.filedropper.com/occ24

http://www.filedropper.com/dx12 - 12 Channel Digital Input Card

http://www.filedropper.com/gbuniversalcontroller

I think that should cover anything in the WMS Stores.

[Mark]

Tried to post these but get told they are too large for the forum.

http://www.filedropper.com/occ15

http://www.filedropper.com/occ17

http://www.filedropper.com/occ22

http://www.filedropper.com/occ23

http://www.filedropper.com/occ24

http://www.filedropper.com/dx12 - 12 Channel Digital Input Card

http://www.filedropper.com/gbuniversalcontroller

I think that should cover anything in the WMS Stores.


grumble grumble missed defrost...

Hi Mate,
hows it going?
Kind Regards
Mark

[Silhouette]

Thanks for all the info fellas, most appreciated! :)

Mel.

[Silhouette]

Hi Mark (Mr. Moderator sir!),
It's going quite well thanks, how about yourself?

Regards,
Mel.

[Ian_Eb]

Missed defrost...

Thanks for that just before bedtime!

[install monkey]

why would i want to see a hyperlink to a book designers????-
Book Designers (http://concept-designs.com.au/book-design-and-layout/)

[hookster]

;) you probably just need a library card IM to see what a book actually looks like!

[install monkey]

im still trying to use crayons- they dont come with instructions and i keep choking on em!!:o
;) you probably just need a library card IM to see what a book actually looks like!